Where is the distributor pickup coil?

They are located inside the distributor and function as the trigger for the ignition system to produce spark. The pickup coil monitors the rotation of the distributor and triggers the ignition system at the optimal moment to produce the best timed spark for best engine performance.

How do I change an ignition pickup coil?

Method 1 of 2: Replacing the ignition pick-up in the vehicle

1. Materials Needed.
2. Step 1: Disconnect the battery: Remove the negative terminal on the battery.
3. Step 2: Remove the distributor cap and rotor.
4. Step 3: Remove the ignition pickup coil: Disconnect the electrical wires to the pickup.

How do you check a distributor pickup coil?

On distributors with the pickup separate from the module assembly, you can check the pickup using your Ohm meter. Connect the leads from your Ohm meter to the 2 leads of the pickup. If you show a resistance of 50 to 200 Ohms, the pickup is functioning correctly.

How do I know if my distributor pickup coil is bad?

Signs of a Bad Pickup Coil

1. No Engine Spark. The pickup coil sends the signal from the ignition module to the spark plugs during the ignition process.
2. Rough Idle. Because the spark plugs are not communicating proper timing to the fuel injectors, a rough idle may occur.
3. Engine Stall/Failure to Accelerate.

How many spark plugs does a 4.7 Dodge engine have?

There are 16 of them, plus the leads from the dual coils. That engine has 16 spark plugs, 8 on each side of the cylinder head. It is an Ambassador Dual-Ignition 8.

How do I know if my pickup coil is bad?

What are the symptoms of a bad ignition coil?

Ignition Coil Problems, Symptoms and Solutions

• Engine misfires.
• Rough idle.
• A decrease in car power, especially in acceleration.
• Poor fuel economy.
• Difficulty starting the engine.
• Check engine light is on.
• Exhaust backfiring.
• Increased hydrocarbon emissions.

What happens when the ignition coil fails on a Dodge Dakota?

On Dakotas that have a distributorless ignition system, a single coil is used to fire two spark plugs. When one of these coils fails, the result is a steady miss on the related cylinders, rough running, and reduced performance. If testing reveals two dead cylinders connected to the same coil, then that coil is faulty.

What kind of ignition system does Dodge Dakota use?

The Dodge Dakota has in the past relied on a traditional ignition system that utilizes a single coil to produce the spark at the spark plugs that is responsible for ignition of the fuel and air mixture. In the early 2000s, however, the Dakota ignition system was switched to a distributorless version that has proven to be more reliable.

Where can I get parts for my Dodge Dakota?

RockAuto ships auto parts and body parts from over manufacturers to customers’ doors worldwide, all at warehouse prices. Easy to use parts catalog.

How do you replace an ignition pickup coil?

Step 1: Disconnect the battery: Remove the negative terminal on the battery. Step 2: Remove the distributor cap and rotor. Step 3: Remove the ignition pickup coil: Disconnect the electrical wires to the pickup. Step 4: Replace the pickup coil: Install the new pickup coil, making sure the wire connectors and mounting screws are properly tightened.

Can a Dodge Dakota ignition coil be replaced?

Turn to AutoZone to repair your truck and get back to work. AutoZone knows the importance of the Dodge Dakota ignition coil. This small part connects the spark plugs and the battery. Without it, your truck starts to stall out, fail to start or lose power. Get a replacement from AutoZone quickly and easily when you order from us online.

How to test the ignition coil on a Dodge van?

The ignition coil on your Dodge Ram Pick Up, Ram Van, Dakota with the 3.2L, 5.2L, or 5.9L engine can be easily tested on the vehicle. You don’t need any expensive testing equipment like a scan tool. Not only that, the test can be accomplished in 4 easy tests, the results of which will let you know if the ignition coil is truly fried or not.

Where is the camshaft sensor on a 1998 Dodge Dakota?

The camshaft position sensor is a key component of the ignition system on your 1998-2003 3.9L Dodge Dakota and 1998-1999 3.9L Dodge Durango. This bad boy is located in the distributor and testing it is not hard since it can be tested with a simple multimeter.

How can you tell if ignition coil has failed?

The cool thing is that you can check to see if the ignition coil has failed (and thus causing your Dodge pickup, van, or SUV from starting) by checking for two very specific things: spark and the switching signal and in this tutorial I’ll show how. OK, let’s turn the page and start the first ignition coil test.