Where do you put the alternator belt on a four cylinder car?

Many four cylinder vehicles have transverse mounted engines, meaning the engine is mounted at a ninety degree angle from the chassis, placing the belts on the side of the engine bay instead of the front. Look for cracks in the belt. A significant sign that your alternator or serpentine belt needs replacing is visible cracking along the belt.

Where do you change the alternator on a Honda Civic?

Replacing your alternator does not require any specialty tools. It can be a lengthy job, and also requires a lot of work inside the engine bay. So if you don’t feel comfortable being underneath the car, then it is recommended having this done at a repair shop. Locate the appropriate spot underneath the car to jack up your Civic.

What happens if you put the wrong belt on your alternator?

Different vehicles have different sized belts and installing the wrong size could result in failing to power the accessories or even damage to the engine. If your old belt was loose because it had stretched over time, take that into consideration when comparing the two belts.

How do you relieve tension on an alternator belt?

If your vehicle does not have an auto-tensioner, you can still relieve the tension on the belt by loosening the bolts attaching the alternator to the engine. As you loosen the bolts, tilt the alternator forward to create slack in the belt.

How do you remove a serpentine water pump belt?

If it is a serpentine belt, remove the belt by using a breaker bar and turning the tensioner to relax the belt. If the vehicle has a v-belt, loosen the tensioner to relax the belt. Step 6: Remove the belt or belts from the pulleys. Step 7: Locate the tensioner to the belt.

Do you need to replace the water pump belt?

The water pump of any vehicle is a critical mechanical part that can last a very long time without having to be replaced, as long as the water pump belt is replaced as recommended by the manufacturer.

What to do if your alternator belt is loose?

If you notice any of these symptoms, the best thing to do is have your alternator belt replaced immediately. Otherwise, you could find yourself stranded somewhere after your vehicle’s electricity shuts down.

How to replace alternator belt if air conditioner is broken?

How to replace alternator belt if the air conditioner is broken, you can use a short serpentine belt without air conditioning. How to replace alternator belt if the air conditioner is broken, you can use a short serpentine belt without air conditioning. Skip navigation Sign in Search Loading… Close This video is unavailable. Watch later Share

How do you check the tension on an alternator belt?

Check the belt tension. Once you have released the auto-tensioner or tightened the alternator bolts, check the tension of the belt to make sure it has seated properly on all pulleys. Pinch the belt between your thumb and index finger and try to wiggle it. There should be very little give to a properly installed alternator or serpentine belt.

Can a serpentine belt be used for an alternator?

If your vehicle has an alternator belt instead of a serpentine belt, this is the method you will need to use. Be careful not to damage the wiring going into the alternator. The alternator provides the power the engine needs to run through those wires. Slide the belt off of the pulleys and remove it from the car.

What’s the best way to remove and replace an alternator?

Follow these simple, step-by-step instructions for removing and installing an automobile alternator with common tools. Includes advice on the correct wiring as well as testing and troubleshooting tips. Sponsored by BBB Industries – makers of premium alternators and starters that meet or exceed OE form, fit and function. http://www.BBBind.com

How is the serpentine belt in a Chev?

Pictures, diagrams of serpentine belt routing. 2.4L. Belt Diagram 3.4 DOHC Cam Engine Drive Belt Diag… 3.5L Engine Serpentine Belt in Chev… 4.2L Inline Six Cylinder Engine Bel… 3800 V6 Belt Routing Picture and Ro…

How to stop alternator belt squeaking and chirping?

How To STOP ALTERNATOR BELT Squeaking & Chirping Noise FOREVER!!! – YouTube How To STOP ALTERNATOR BELT Squeaking & Chirping Noise FOREVER!!!

How do you tighten the belt on an alternator?

Tighten the alternator bolts. With the serpentine or alternator belt safely seated on the alternator pulley, use the same wrench you used to loosen to the bolts to tighten them again. As you tighten the bolts, the alternator will stop tipping forward, which will increase the tension on the belt.

Where does the serpentine belt go on an alternator?

If you do not have a diagram on the vehicle or in your service manual laying out the direction your serpentine belt travels through the pulleys, take a picture of it with your phone to refer to when installing the new belt. A strictly alternator belt will likely only go around an alternator pulley and the crank pulley at the bottom of the engine.

Where is the alternator located on a car?

Feel underneath the alternator to find the bolt that mounts the alternator to the frame. Make sure it is in place and that the rear nut is firmly attached. Loosen the nut on the top bolt of the alternator that passes through a “track” and allows you to position the alternator.

Can a car have more than one alternator belt?

In older model vehicles, engines often came equipped with multiple belts that each powered a different accessory. However, most modern vehicles use only one belt to power the alternator as well as the power steering, air conditioning, and any other accessories.

How do you find the negative terminal on an alternator?

The negative terminal can be identified by looking for the negative symbol (-) or the letters NEG. Loosen the bolt until you can slide the cable off of the terminal. Tuck the cable to the side of the battery to prevent it from coming in contact with the negative terminal.

What’s the best way to loosen an alternator belt?

Use a breaker bar or socket wrench to loosen the auto-tensioner. Many newer model vehicles come equipped with an auto-tensioner pulley. The pulley presses upward as the belt wraps around it so the belt remains under constant, steady tension.

How to replace an alternator on a 1995 GMC?

Somewhere on your vehicle there is a tensioner pulley. You’ll need to move it enough to slip the belt off the pulley. Our ’95 GMC has a standard spring-loaded GM tensioner that required us to pull it back with a wrench.

How many bolts do you need to replace an alternator?

Our model required the removal of three bolts: one at the front and two at the rear. With the old alternator in your hand you’re half way home. You’ll likely find getting the new one back in goes much faster since you already know what size the bolt heads are and where everything is.

When did GMC Sonoma change the name to Sonoma?

In 1992, the GMC S-15 was finally renamed into GMC Sonoma. This change in name was surrounded by many notable upgrades in the model. Anti-lock brakes were integrated into the rear wheels for increased driver control and safer handling. It also featured a five-speed manual transmission for fuel economy.

Where is the serpentine belt on a V6 engine?

Depending on the make and model of the vehicle, this belt (often called the serpentine belt) is often located on the front or side of the engine. Many American made vehicles with V6 engines or larger have the serpentine or accessory belts on the front.

How do you remove a serpentine belt from a car?

Pull the belt off of the pulleys. With the tension relieved from the belt, pull it off of the pulley that has been placing tension on it, then remove it from the around the rest of the pulleys on the engine. If the belt is severely damaged, be sure to remove any parts that may have come off of it as well.