Where do I get the Immobilizer brake code?

Have the customer get the “Immobilizer Brake Code” from the dealer or Honda Customer Relations. You will need the Vehicle Identification Number. This is a five digit number code. Each car has a different “Immobilizer Brake Code” since they are VIN specific. 3.

Can you cancel the Immobilizer on an Acura?

Yes, only temporarily in an emergency situation, if the customer has lost his key (s) and the car must be moved. Important: To maintain security of the vehicle, the immobilizer cancel function can only operate with a special VIN based cancel code which can be obtained from The Acura Tech Line.

What does the VIN number on an Acura tell you?

Every Acura car has a unique identifier code called a VIN. This number contains vital information about the car, such as its manufacturer, year of production, the plant it was produced in, type of engine, model and more.

What is the cancel code on an Acura?

Customer advised to have a key cut from a regular key blank and enter the cancel code using the ignition switch and foot-operated parking brake as follows: Example – cancel code is 54345. a) Insert the new key in ignition switch and turn to ON (II) position. Indicator light flashes continuously after the initial 2 sec. indication.

What are the keys on an Acura 3.5RL?

This is how the immobilizer system works. The 3.5RL is supplied with three keys and a key number plate: 1. A master key (black) for ignition switch, door locks, glove box and trunk lock. 2. A valet key (grey) for ignition switch and door locks. 3. A packaged learning key (red) for re-coding the immobilizer system only.

Are there any problems with the Acura TSX 2004?

The issue appears to be most common on 2004 models. Repairing this can be troublesome, as, depending on the issue, removal of the instrument cluster will be required. In more severe cases, it’s an issue of the wiring and board setup powering the cluster, that can require repairs.

When does window motor fail on Acura TSX?

The window motor module failure appears to occur most often on 2005 TSX models before the 20,000 mile mark. Symptoms may include failure of the passenger’s side door lock. There is not much in the way of preventative maintenance here, just have to pony up and replace it. Figure 3. The window motor module may fail.

What causes squeaky leather on Acura TSX?

Figure 1. Squeaky leather. Another relatively common problem is a click in the clutch pedal during travel. One owner explains that the click is often felt when the clutch pedal is depressed, particularly when the weather is warmer. This issue may be resolved with extra lubrication of the plastics associated with the movement of the clutch pedal.

Where is the transponder code on an Acura?

The key’s transponder code is registered in the immobilizer unit of the vehicle. If this signal is correct, the immobilizer control unit will connect the starter and PGM-FI circuits when the ignition is switched ON. Important: The learning key (red) will not start the engine and must only be used for re-coding the system.

How do you enter the brake code on a car?

Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 2nd number in the BRAKE CODE. 7. Turn the ignition switch to the LOCK position. 8. Within 30 seconds, turn the ignition switch to the ON position (II) and enter the 3rd number in the BRAKE CODE.

How does the Immobilizer work on a Honda?

Each master key and valet key has electronic circuits in its grip that output a rolling-type code (set by the immobilizer control unit-receiver) when you insert the key into the ignition switch. The immobilizer system uses this code to determine whether to start the engine.

What to do if your Honda i-HDS immobilizer is not logged in?

If your i-HDS is not logged in to the iN, you will have to enter the PCM code you have retrieved from the iN Immobilizer Code Inquiry to proceed. When you are finished, turn the ignition switch to LOCK (0), then turn off and disconnect the i-HDS. NOTE: Refer to the parts catalog for the P/Ns, and search by VIN for the correct parts.

How do you add a key to a Honda immobilizer?

Use the Honda Diagnostic System ( i-HDS) with Honda key blanks to add a key. The i-HDS rewrites the immobilizer control unit-receiver, storing the transponder code of the new key in the memory of the immobilizer control unit-receiver.

How does the Immobilizer work on a Honda i-HDS?

There is no direct electrical connection. Once the electronic transponder is energized, the key sends its ID code to the immobilizer control unit-receiver, which checks the code against the codes stored in its memory. If the codes match, the immobilizer control unit-receiver sends a unique serial code to the ECM/PCM.

What does serial code mean on Honda immobilizer?

If the codes match, the immobilizer control unit-receiver sends a unique serial code to the ECM/PCM. But if the transponder ID code does not match, no serial code is sent, and the vehicle won’t start.