When to turn off the radiator fan in Acura TL?
It does not close the circuit to ground until the coolant reaches about 225 deg. F. This is the switch that will keep the cooling fan running after the engine has been turned off if the engine is really hot. A cool way to add a tachometer is to swap in a gauge cluster from a 1996 Acura TL.
Why does my car not start after warm?
Car will sometimes not start after warm. When i start my car, for the first time during the day- I have no problem. When I go somewhere and shut it off, sometimes it won’t resatrt. It doesn’t seem to matter what the weather is outside, it just does it when it feels like it.
What was the water problem at Woodstock 99?
The Water Problem. With about 220,000 people in attendance and another 10,000 working the festival, Woodstock ’99 temporarily made the festival site the third most populated city in New York state.
When to restart a car with a temp problem?
If you pay close attention you will notice that when you make a short stop say 5 minutes that is when you have restart problems . As long as you hold idle for a few minutes with gas pedal everythings OK. I am almost certain a temp part is the problem. If my car sits 30 minutes or more never a problem. Any one witn addl thoughts. Please jump in.
Why is my Chevelle 350 hard to start?
Fuel pump check valve doesn’t maintain pressure in the fuel rail so it boils and then you have to crank excessively to get rid of the vapor before it will start. Bought a 1972 Chevelle 350 a couple years ago. Every time I drove it it wouldn’t restart easily or sometimes not at all unless I waited a while.
What does it mean when your hot tub stops running?
If you set the temp. to 100F and it stopped heating then update me if it over-heats again. That is how is should work, so that is a good sign. If perhaps the jets were running while the cover was closed for a relatively long period of time, that can over heat the tub too from the friction of the water rushing through the pipes.
When does your car run hot or cold?
If you are like most drivers, our guess would be almost never. Most drivers look at their temperature gauge so rarely that many vehicle manufacturers don’t even include temperature gauges any more but just lights that will come on if your car is either extremely cold or extremely hot.
What happens if the fan on my radiator fails?
The most common symptom of a faulty cooling fan motor are cooling fans that do not come on. If the cooling fan motors burn out or fail, the cooling fans will be disabled. The cooling fan motors work together with the cooling fan blades to pull air through the radiator. If the motor fails the blades will not be able to spin or generate air flow.
When does the radiator fan close to ground?
This thermo-switch is set to close the circuit to ground when the coolant reaches about 200 deg.F. The secondary thermo-switch for the cooling fan is located where the upper radiator hose attaches to the engine. It does not close the circuit to ground until the coolant reaches about 225 deg. F.
How to test if a Honda radiator fan is working?
Here is how to test if the fan is functioning properly: 1 Unplug the radiator fan connector. 2 Run jumper wires between the connector’s two electrical terminals. See Contact Test in Step 1. 3 If the fan does not turn on, you will need to replace it.
What does it mean when your radiator fan is not working?
This is what we call a blown fuse. A blown fuse is no big deal, and changing one does not cost a lot of money. If your car’s radiator fan is non-functional, check your car’s user manual and locate the fuse for the radiator fan controller or the fan.
Is there a way to test a radiator fan?
You can test the electrical radiator fans by taking a wire from the car battery, unplug the radiator fan connector, and put 12v+ and ground into the connector. This is the fastest and easiest way to test your radiator fans. Because the radiator fan is often drawing so much power, there is often a relay that is powering the coolant fan.
Where is the relay on a radiator fan?
The fan relay is often located in the engine bay’s fuse box, but the best way is to check your repair manual to find where it is located. Testing a 4 pin relay is often very straightforward. Remove the relay and give 12 volts to pin 30 and 85. Ground pin 86 and check if there is voltage coming out from pin 87.