What kind of aluminum intake manifold do I Need?

Aluminum intake will work with all Vortec cylinder heads, including P/N 12558060, P/N 19300956, P/N 19300955, P/N 19331470, or P/N 19331472 NOTE: The exhaust manifold from 1996-and-newer pickup trucks with RPO L31 350 engine, P/N 12557828, is drilled and tapped to accept an EGR tube.

How to replace a small block engine intake manifold?

NOTE: Replacing the ECU on MEFI 3 Ram Jet engine P/N 12495515 requires using new wire harness kit P/N 12499116, or use jumper wire P/N 88963118 to use MEFI 4 ECU as an open-loop system. Includes ECU module P/N 88962717, wire harness P/N 88961967, oxygen sensor P/N 19178918, intake air temp sensor P/N 25036751, and oxygen sensor fitting P/N 15156588

What kind of gasket to use for intake manifold?

Gaskets that can be used with this manifold are: Fel-Pro® P/N 1205 and P/N 1206, and Mr. Gasket® P/N 102. Always match the gasket to the cylinder head you plan to use to ensure a correct fit.

Is there an open carburetor spacer for dual plane intake manifolds?

NOTE: Open carburetor spacer is not recommended for use with dual-plane intake manifolds. Designed for 283-400-cubic-inch engines using Vortec cylinder heads P/N 12558060, P/N 19300956, P/N 19300955, P/N 19331470, or P/N 19331472

What kind of engine does nastyz28 454 have?

I bought a couple of engines and finally stuck with a 454. I had it rebuilt by a friend with 11:1 free floating forged pistons, Isky Z33 cam, LS6 original intake, Mallory distr (tuned with advance curve to match my stall convertor), Holley 750 Dual feed double pumper carb and Turbo 400 trans with a 3500 TCI convertor.

What kind of gasket do I need for a small block intake manifold?

Runners in heads and manifold must be matched by engine builder. Often, the gasket will line up with the top of the port so removal is required at the bottom of the port. Gaskets that can be used with this manifold are: Fel-Pro® P/N 1205 and P/N 1206, and Mr. Gasket® P/N 102.

What are the casting numbers for Chevy small block V8?

Different chamber volumes, port volumes, port locations, valve sizes, etc. were used. Check this casting carefully to determine which features it may have.

What kind of intake manifold does a Chevy small block use?

Intake Manifold, Victor Jr., Single Plane, Aluminum, Natural, Square Bore, Chevy, Small Block, Each Need It Sooner? Need It Sooner? Need It Sooner?

When did nastyz28 build his 1971 Camaro?

This thread will be dedicated to the build process of our 1971 Camaro that is ultimately being built for autocross and road race events. We aquired this car in spring of 2015 from a Spring Carlisle swap meet, unfortunately it has taken us until late 2016 to finally start the build process.

What’s the difference between low rise and medium rise intake manifolds?

Spread bore intake manifolds match that shape to accomodate the larger venturis toward the back. Low Rise Intakes Low Rise refers to the height of the intake. Low rise is a general term used to describe intake manifolds. There is no clear distinction between a low rise and a medium rise intake.

What is the p / n 12363406 engine intake manifold?

Same as P/N 12363406 (see previous page), except it has been CNC-port-matched for GM aluminum oval-port heads with large oval-port heads (1975-and-older), and all aluminum heads with oval-ports NOTE: Open carburetor spacer is not recommended with use of dual-plane manifolds.

Which is the best intake manifold for street racing?

Dual plane intake manifolds are the most popular for high performance street and mild racing because they generally build power across a wider range and start at 1,500 RPM, depending on the dual plane manifold. Each intake manifoldhas its own performance characteristics. It’s best to know how you’ll use your vehicle and select from there.

How much is the intake manifold on a Chevy?

Chevy Intake Manifold, Vortec Head Design $541.27 Quick View Chevy Small Block Intake Manifold, Vortec Head Design (Dual Pattern Carb Mount) $422.55

How tall is the intake manifold on a corvette?

Designed for all 396-502 engines with GM aluminum heads (1975 and earlier) and large oval-port iron heads NOTE: May not fit on many Corvette models. Manifold height is 6″ at the rear and 4.5″ in front. Check for hood clearance before ordering. NOTE: Open carburetor spacer is not recommended with use of dual-plane manifolds.

Are there any new front throttle intake manifolds?

1 new custom built Billet Runner CNC injector bungs into runner, removable… 1 new custom built front throttle body sheet metal intake designed for a… (Comparison pictures are of the MM3 intake sitting next to an Edelbrock…