How much HP can a 302 make?
Standard Ford 289 and 302 small-blocks were factory-rated between 200 and 230 hp. The vaunted 289 High-Performance engine was said to make 271 hp. Today, if a 302 Ford makes 360 hp on pump gas with a hydraulic cam, most experts consider it to be a pretty good motor-at least until Joe Sherman steps up to the plate.
How much coolant does a 1966 Mustang take?
Registered. ’65-66 Mustang cooling system capacity, including the heater, is 16 quarts.
How much power can a 69 302 block handle?
As indicated already, a stock 302 block (all years – even the touted Mexican block) will hold 450-550 hp with a good tune.
How much coolant does a 67 Mustang take?
| Engine lubricant oil capacity: | 4.2 liter / 4.4 U.S. qt / 3.7 imp. qt |
|---|---|
| with filter change | |
| Engine coolant capacity: | 9 liter / 9.5 U.S. qt / 7.9 imp. qt |
| Fuel tank capacity: | 64 liter / 16.9 U.S. gal / 14.1 imp. gal |
| Battery capacity (Ah): | 45 |
How much antifreeze do I need for engine coolant?
If you are topping up a reservoir that isn’t empty, use the same antifreeze as last time. Different coolants can mix to produce dangerous chemicals that can cause engine damage. Explore different antifreeze types here. Most cooling systems will hold around 5 litres.
What kind of coolant does a Motorcraft engine use?
G = Green-colored engine coolant approved to Ford specification ESE-M97B44-A (Motorcraft® Premium Antifreeze/Coolant) O = Orange-colored engine coolant approved to Ford specification WSS-M97B44-D or WSS-M97B44-D2 (Motorcraft® Orange Antifreeze/Coolant)
How much coolant do I need to fill a new radiator?
A: You should add a 50/50 mix of coolant in an amount equal to that which you drained out in order to perform the needed maintenance to the cooling system. Regarding this, how much coolant does it take to fill a radiator? If the fluid is not at the top of the opening, fill the empty space with 1 part antifreeze and 1 part distilled water.
What are the standards for cooling a rotating motor?
The different methods of cooling rotating machines are classified in the standards IEC 34.6 and AS 1359.21. For AC induction motors, cooling air is usually circulated internally and externally by one or more fans mounted on the rotor shaft.
G = Green-colored engine coolant approved to Ford specification ESE-M97B44-A (Motorcraft® Premium Antifreeze/Coolant) O = Orange-colored engine coolant approved to Ford specification WSS-M97B44-D or WSS-M97B44-D2 (Motorcraft® Orange Antifreeze/Coolant)
What do you need to know about engine coolant?
Engine coolant must be engineered to inhibit corrosion of internal engine passages, and neutralize acids and other byproducts of combustion. And the coolant itself must have an extended service life. Combine all those requirements and you can begin to see that modern engine coolant is a robust but complicated fluid.
How do I know how much coolant to add to my radiator?
Any time you add coolant to the radiator, it?s a good idea to start the engine. You should be listening for any usual sounds, primarily from the cooling fans. Humming or clanging noises could indicate a problem with the cooling system. Check for leaks.
What kind of water pump does a Boss 302 have?
Beginning in 1970, 302 and 351W small-block Fords received a new water pump casting (D0AZ-8501-C) with the inlet on the left-hand side of the engine. Boss 302s for 1969 were fitted with a 1969- specific high-flow water pump (C9ZZ- 8501-A).