How do you replace the brakes on a 1998 GMC Sierra?

Replacing the brakes on the 1998 GMC Sierra is a relatively easy task. Open the Sierra’s hood and remove approximately half of the fluid from the brake master cylinder using a turkey baster. Place this fluid in a clean container for reuse. Loosen the front lug nuts with a ratchet and socket, but don’t remove them yet.

How do you replace a brake line in a Dodge Caravan?

Plug the holes in the brake line on the van so you won’t lose or contaminate the brake fluid. Use rubber, non-absorbent cloth or any clean material that won’t absorb the fluid. Attach the new brake line pipe. Screw the bolts on by hand and then tighten them with your wrenches.

Do you need to change the brake pads on your car?

Changing the brake pads on your vehicle isn’t as complicated as you may think. When choosing a new vehicle, lots of people make their decisions with airbags, crumple zones, and several other safety features in mind. But many take for granted one of the most important safety systems a vehicle can offer — the brakes.

How do you change the brake pads on a car?

New brake pads should always be greased at their contact points, in addition to greasing the caliper guide pins and replacing the brake pad hardware, if applicable. Once the caliper has been compressed, you can then replace the caliper and caliper bolts, bleed the brakes, and replace the wheel.

How do you change brake fluid in a car?

To change the brake fluid, you will need a way to pull as much of the old fluid as possible from the master cylinder reservoir. Once that is completed, you can refill the reservoir and begin bleeding the brakes until the new fluid has reached each caliper or wheel cylinder.

When to know if your brake pads need to be replaced?

Regardless of how long it has been since you changed your brake pads, they should be inspected and serviced when you notice symptoms of failure. A visual inspection can confirm if the brake pad’s friction material is worn down, and severely worn brake pads may even contact the rotor and cause further damage.

How do you replace brake pads on a Chevy truck?

Slide the new brake pads onto the sides of the caliper and return the caliper to its position on the caliper bracket. Screw in the caliper bolts and tighten them with the ratchet and socket. Check the master cylinder. The level of fluid in the reservoir will have been raised by opening the caliper piston.

How do you replace brake pads on a ram 2500HD?

Figure 4. Use the C-clamp to compress caliper piston (Ram 2500HD shown for reference). With the caliper free, the brake pads can be replaced. The inner brake pad simply pops into the caliper piston via a spring clip, and can be easily removed by pulling it away from the piston.

Are there disc brakes on a 1996 Chevy truck?

Chevy pickup trucks from the 1996 model year are equipped with anti-lock disc brakes on the front wheels of the trucks. The disc brakes employ a system that forces the brake pads against the rotors when the brake pedal is depressed. Brake pads that are worn will not have the brake pad material necessary to consistently stop the vehicle.

Is there a full rear drum brake replacement?

88-98 2500 3500 Rear Drum Brake Replacement FULL HOW TO! – YouTube 88-98 2500 3500 Rear Drum Brake Replacement FULL HOW TO! If playback doesn’t begin shortly, try restarting your device.

How do you replace the brake on a Dodge Ram?

Rear brake assembly. 1. Disengage the secondary shoe return spring from the anchor pin. Figure 5. Secondary spring. 2. Disengage the primary shoe return spring from the anchor pin. Figure 6. Primary spring. 3. Push in on the hold-down retainer and turn it 90 degrees and remove the retainer, spring, and pin.

How is the emergency brake applied on a truck?

The emergency brake on a drum-disc-equipped truck is applied using the brake shoes on the rear brake assembly that are also used when you apply the brakes normally while driving. The only difference is that there is a cable that actuates them when you apply the emergency brake versus hydraulic pressure when you apply the brakes while driving.

When is it time to replace a brake master cylinder?

The brake master cylinder is a key component of a vehicle’s brake system. If this component fails, then your vehicle’s braking ability will be weakened or destroyed. To avoid this safety hazard, it is best to replace the brake master cylinder.

Where is the brake fluid in a master cylinder?

Locate the brake fluid reservoir, the brake master cylinder, the brake fluid level sensor, and the brake fluid lines. The brake fluid reservoir is usually at the top of the brake system and contains brake fluid. It can be identified by the presence of a threaded cap on top of it.

Why does my brake pedal get soft when the master cylinder wears out?

The rubber seal on the master cylinder wears out with the time. And, if these seals are not replaced timely, they may contaminate the brake fluid. Thus, causing the pedal to get soft and doughy or slowly sinking to the floor.

What kind of wrench do I need to replace master cylinder?

Then, use a swivel extension to unfasten the master cylinder from the brake booster, if your vehicle has one. For most brake lines, a 10-mm flaring wrench will work. It’s much easier to use a flaring wrench than a regular open-ended wrench for this.