How do you change a power steering pump pulley?

1. Step 1: Disconnect the battery and lift the vehicle.
2. Step 3: Remove the serpentine belt or drive belt.
3. Step 5: Remove the mounting bolts on the power steering pump bracket.
4. Step 7: Lubricate the input shaft.
5. Step 9: Tighten the pulley installation nut.
6. Step 11: Install the new power steering pump, pulley and belt.

How do you remove a power steering pulley nut?

Because the pulley rotates freely, it is impossible to loosen this nut unless you have a grip on the pulley while you turn the securing nut counter-clockwise. Stop the pulley from spinning while you remove the nut, and the nut will become loose and the pulley can be freed from the power steering pump shaft.

How do I know if my power steering pump pulley is bad?

Watch for the following symptoms if you suspect a bad or failing power steering pump pulley.

1. Burning smell from engine. A burning smell from the engine means the belt is not tight enough or the power steering pump pulley has seized.
2. Choppy steering.
3. Steering fails completely.

How much does it cost to replace a power steering pump pulley?

Expect to pay between $100 – $250 or so for labor costs on this job. The parts are where you will really have to pay out though. You will pay anywhere from $150-$600 for most power steering pumps and the other parts needed to replace an old pump.

What does a bad power steering pulley sound like?

A loose power steering pump pulley or mounting bracket will make a rattling sound too. A rattle sound can be caused by a loose rack due to wear. It could also indicate a loose serpentine belt or idler pulley bearings beginning to fail.

How much does it cost to replace power steering pulley?

Power Steering Pump Pulley Replacement pricing for various cars

What causes a power steering pump to go bad?

Since your power steering pump is a simple machine, the most common cause of failure for a power steering pump is the bearing going bad. When they get very worn, they can cause leakage around the pump shaft behind the pulley and even allow the pulley to wobble.

Can you drive with a bad pulley?

A damaged pulley can cause the drive or serpentine belt to dislodge. The safety recommendation is not to drive the car at all and take it to a mechanic immediately. You should be concerned if the vehicle makes squeaking or rattling noises. The car can still run for months or break after a few days.

What is the average cost to replace a power steering pump?

between $492 and $682
The average cost for power steering pump replacement is between $492 and $682. Labor costs are estimated between $148 and $187 while parts are priced between $344 and $495. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed.

How do you remove drive belt from power steering pump?

Use a socket and ratchet to loosen the adjuster bolt of the power steering pump and pulley. When this adjustment bolt is loosened, the pump will pivot on an axis, making it possible to loosen its drive belt. Pull the drive belt off of the power steering pump pulley. With the drive belt removed from the pulley, the pump easily pivots in place.

How do you replace a power steering pulley?

Replace the old power steering pulley with the new performance pulley. Grasp the new pulley with a rag and vice grips to hold the pulley in place while you tighten the securing nut on the pump shaft until tight. Loosen the adjustment nut and wrap the pulley with the drive belt.

How do you remove a power steering line from a car?

Tighten the center bolt of the puller with an adjustable wrench in a clockwise direction until the pulley loosens from the pump. Remove the puller and pulley from the engine bay. Remove the two power-steering lines from the pump by loosening the hose fittings at the pump with a tubing wrench turned in a counterclockwise direction.

What do I need to replace a power steering pump?

Power Steering Pulley Puller set (to remove and attach the pulley). Some auto parts stores will loan the tool sets. Socket set. Open end wrench set (for use with puller set). Leverage pipe or extension bar (in case the pulley is hardened on the spindle).

How do you remove a pulley from a power steering pump?

First, place the power steering pump in a vice on a work bench. Attach the pulley removal tool to the pulley. Guide the locking nut onto the edge of the pulley. Using a socket and ratchet, slowly loosen the pulley while holding the pulley attachment nut with a corresponding end wrench.

Where is the serpentine belt on a power steering pump?

To remove the serpentine belt, loosen the tensioner pulley that is located on the left side of the motor (as you’re looking at the motor). Once the tensioner pulley is loose, you can slip the belt off rather easily. If your power steering pump is driven by the drive belt, you’ll have to remove this belt as well.

How can I tell if my power steering pulley is broken?

When the power steering pump pulley is wearing out or has broken, it may display a few common warning signs that indicate service is needed. You many notice a whining sound coming from the pump pulley, the power steering feeling tight when driving, or the pulley being damaged when a belt breaks.