Can I replace steel transmission cooler lines with rubber?

You can use rubber hose, but make sure it’s transmission cooler line rated. The pressure is quite low (12-15 psi). Double clamp it or use FI type clamps instead of the worm-drive style.

How do you change an oil cooler line?

Method 1 of 1: Replacing oil cooler lines

1. Materials Needed.
2. Step 1: Jack up the vehicle and set jack stands.
3. Step 2: Place wheel chocks on both sides of wheels still on the ground.
4. Step 3: Locate the oil cooler lines.
5. Step 4: Remove the oil cooler lines at the engine.
6. Step 5: Drain excess oil from the oil cooler lines.

How much does it cost to replace an oil line?

To replace your vehicle’s oil cooler lines, you need to pay between $225 and $253. The part itself costs about 118 dollars, while labor costs might range from $106 to $134. Some vehicles might require up to $400 depending on the complexity of the oil cooler lines and the severity of the problem.

Can you use coolant hose for oil?

Heater hose line is designed for coolant and as such does not get along well with oil. Over time the hose will expand and also harden and become brittle.

How much does it cost to replace transmission cooler lines?

You will pay somewhere between $100 and $450 for a transmission cooler line replacement. The labor should be between $60 and $300, while parts can cost you anywhere from $40-$160.

What causes an oil cooler to leak?

Most oil leaks stem from bad connections or cracked oil pans, engine gaskets or seals. Another place to look is the oil cooler adapter, which connects oil lines and is itself sealed with a gasket. When the problem is a bad oil cooler, oil will puddle on the ground.

Can you use rubber hose power steering?

There are several hydraulic systems in most cars, namely power steering and brakes. Both require high-pressure hoses that can handle 2,000psi or more. Inside a rubber hydraulic line is braided steel to support the pressure of the fluid. Slipping a larger hose over it with hose clamps will just slow down the leak.

Can silicone heater hose be used for oil?

Is silicone hose oil resistant? Standard Silicone rubber is porous and therefore not suitable for oil. This grade is specially formulated to prevent oil from penetrating the wall. Many of our competitors dilute the material to save money, because the FluoroSilicone material is a very expensive material.

Do you need to replace the oil cooler lines?

If the lines go to an oil cooler, it may be necessary to replace the oil cooler as well, particularly if the damage is due to debris buildup. The vehicle is allowed to cool. The vehicle is raised and secured on jack stands. A drain pan is placed under the oil cooler lines.

Where does the coolant go in an oil cooler?

In most vehicles on the road, engine oil is fed to the oil coolers from an adapter that is located between the engine block and the engine oil filter. The oil then flows through the tubes of the cooler while the engine coolant flows around the tubes. The heat from the oil is transferred through the walls…

How are the oil cooler lines connected to the car?

The two oil cooler lines are connected and secured with new clamps to the oil cooler. The vehicle is started and checked for oil leaks then lowered off of the jack stands. The oil level is checked and topped off with the correct oil. The vehicle is road tested for proper operation and the cooler lines are rechecked for any signs of leakage.

When to get a transmission cooler line replacement?

When to Get Transmission Cooler Lines Replacement. Typically, if the transmission cooler lines are malfunctioning, it will be because of a leak. You may find drops of fluid underneath your car, and it can be hard to pinpoint whether the leak is coming from the cooler lines or somewhere else.

Can you use rubber hose for transmission cooler lines?

You can use rubber hose, but make sure it’s transmission cooler line rated. The pressure is quite low (12-15 psi). Double clamp it or use FI type clamps instead of the worm-drive style. Click to see full answer.

Can a rubber line be used for trans fluid?

Trans fluid & regular rubber fuel line aren’t compatible, as it will swell it & leak. If I have to use any hose on the transmission line, I usually flare the steel line before I slip on the rubber hose, it helps to keep the hose from blowing off.

Which is easier to replace rubber lines or steel lines?

The rubber hoses are more readily available and are easier to replace than steel lines. On some equipment you have to take the cab off in order to replace the steel lines. The rubber hoses can last a long time because they absorb the shock and vibration caused by the equipment.

How much pressure is on a transmission cooling line?

How much pressure is on a transmission cooling line? there is at idle between 20-50 psi but during use pressures in transmission lines can reach 100 psi or more. if you are going to use rubber lines be sure to use barbed fittings so the hose does not blow off.