Why does my Chevy have a theft PassLock system?

However proud you are of your GM, you undoubtably know GM’s products well enough that you also know that in spite of how great they are, they almost always seem to have some kind of manufacturing quirk that ends up killing the whole “See the U. S. A. in a Chevrolet” vibe.

What is the system fault code for PassLock security?

When the sensor defect starts, it usually presents itself as system fault code B2960. A red (or yellow) “security” warning light will stay illuminated and the engine will either a) never start or b) start for a moment and then shut down.

How do I Turn Off the PassLock security light?

1. Turn the key to ON and attempt to start the engine and release the key to the ON position. 2. The SECURITY light will illuminate. Wait 10 minutes until it turns off. 3. Turn the key to OFF for 10 seconds. 4. Turn the key to ON and attempt to start the engine. If it starts and run, the system has reset.

What to do if your car won’t start at PassLock?

A red (or yellow) “security” warning light will stay illuminated and the engine will either a) never start or b) start for a moment and then shut down. A temporary fix is to leave your key in the ignition, at the “auxiliary” position for about 10-15 minutes until the security light shuts off.

However proud you are of your GM, you undoubtably know GM’s products well enough that you also know that in spite of how great they are, they almost always seem to have some kind of manufacturing quirk that ends up killing the whole “See the U. S. A. in a Chevrolet” vibe.

Why does my PassLock security light keep going off?

After turning the ignition off for the third time and waiting for twenty seconds, the engine should start and run. If it doesn’t, there may still be something wrong with the system. After the learn procedure is completed and the engine is running, the security light may stay on steady for a few minutes and then go off—this is normal.

When the sensor defect starts, it usually presents itself as system fault code B2960. A red (or yellow) “security” warning light will stay illuminated and the engine will either a) never start or b) start for a moment and then shut down.

A red (or yellow) “security” warning light will stay illuminated and the engine will either a) never start or b) start for a moment and then shut down. A temporary fix is to leave your key in the ignition, at the “auxiliary” position for about 10-15 minutes until the security light shuts off.

Why does my anti theft system not work?

My car has an automatic transmission. Your anti-theft system (pass-lock) may have a fault or it may be the key itself. The keys have a chip embedded in them. When inserted into the ignition, the alarm system looks for codes from the key. Try another key if you have one. If it starts, then the first key is bad and has to be replaced.

How to disable anti-theft system in your car in the right?

Insert the key in the door lock all the way and then turn the key to unlock your car door, but don’t release it. You want to hold the key in the unlock position for twenty to thirty seconds. This lets the car recognize that you have the right key and will disengage and reset the system.

How to reset PassLock reset system on Chevy?

1. Turn the key to ON and attempt to start the engine and release the key to the ON position. 2. The SECURITY light will illuminate. Wait 10 minutes until it turns off. 3. Turn the key to OFF for 10 seconds. 4. Turn the key to ON and attempt to start the engine.

How to bypass factory theft on a GM vehicle?

This is a really unique security system bypass kit that you can use to override your current factory theft system on your GM vehicle. You can get this kit from New Rockies.com . I came across this site surfing the net when I was having a similar issue on a GM vehicle.

Why does my car anti theft system not work?

Your anti-theft system (pass-lock) may have a fault or it may be the key itself. The keys have a chip embedded in them. When inserted into the ignition, the alarm system looks for codes from the key. Try another key if you have one.

Is there a way to bypass GM security system?

Scouts Troop 980 of Utah cheers as their ’92 Olds Toronado is coming back to life. Thanks to the NEWROCKIES Full Bypass Module! How to FULLY bypass VATS Passkey and Passlock Security Systems in GM Cars. Has the dreaded GM Security system just hit you?

How do you turn off PassLock on a Chevy?

Key on, press volume till readout says SETTINGS then scroll to the Security to toggle off by pressing reset ( watch YOUTUBE). I personally see no sense of having no security system so try the RELEARN method. Other thing is that the Ignition Switch has a Sensor on it and the wire clip comes loose.

Where are the wires in a Chevrolet PassLock?

To find these wires, look for three wires that at some point are wrapped together, coming from the ignition barrel. Usually, they are orange/black, red/white, and black. They can also be yellow, red/white, and black. Cut the orange/black wire or the yellow wire, depending on what you have.

Can a PassLock cause a car not to crank?

If the vehicle will not crank, PASSLock cannot cause this condition. If the vehicle starts, but stalls quickly, this condition can possibly be related to PASSLock. Most PASSLock-equipped vehicles have a telltale indicator in the instrument panel.

How does the PassLock system on a 2000 Chevy Silverado work?

by David Clair. The 2000 Chevrolet Silverado is equipped with the General Motors Passlock theft-deterrent security system. The system disables fuel to the ignition if a valid key is not used when attempting to start the engine. If the Passlock system is activated, the Silverado will not be able to be started until the system is reset.

Where is the PassLock switch on a Chevy?

The switch allows the car’s passlock system to be switched on or off by splicing with a yellow wire that’s plugged into the cylinder lock. Once completed, the new switch should be placed underneath the dash right below the key hole.

Is there a problem with the PassLock sensor?

The short answer is there’s a problem with the sensor. Some have suggested that the pins in the system are “tin” plated and subject to oxidization over time. Others say their system is possessed by the devil and in need of an exorcist.

Why is my GM anti theft not working?

When the anti-theft system light stays on, the fuel pump won’t pump and injectors don’t activate to prevent theft. 2. Sometimes the GM (General Motor) Passlock system cars have a part around the ignition tumbler that goes bad and no longer detects the valid key, due to “the battery in the key is dead and the chip is not connecting to your computer”

What do you need to know about GM vehicle theft deterrent?

Connect a battery charger to the battery to ensure power is available while programming. Both the IPC/BCM and PCM must be working and communicating with each other. 1. Turn ignition on. 2. Attempt to start the engine, and then release the key to the “ON” position. 3. Observe the “SECURITY” indicator light.

Why is the theft light not blinking on my Chevy Malibu?

It’s not uncommon to have a glitch in the theft passlock system that prevents owners from starting their vehicles. It’s a pesky problem, but easily dealt with when you bypass the system. Initially you’ll notice with the late-model Malibu in our featured video is that it won’t start until the theft light stops blinking.

How much does it cost to replace an antitheft system in a Chevy Tahoe?

The average cost for a Chevrolet Tahoe antitheft system control module replacement is between $294 and $327. Labor costs are estimated between $123 and $155 while parts are priced at $171. This range does not include taxes and fees, and does not factor in your unique location. Related repairs may also be needed.

How to reset anti theft system on a 2008 Chevy Fixya?

This link explains it pretty well. Turn ON the ignition, with the engine OFF. Attempt to start the engine, then release the key to ON (vehicle will not start). Observe the SECURITY light, after approximately 10 minutes the light will turn OFF. Turn OFF the ignition, and wait 10 seconds.

What to do if your anti theft system is locked up?

If the anti-theft system has locked up your engine, you won’t be able to start it. You’ll have to disable it with these steps. Step 1: Check for the anti-theft light. It’s located on your dash and will have a blue or red light. Step 2: Turn the ignition to the “on” position.