Where is the water pump located on a 2001 Pontiac Grand Prix?

The water pump is just above the crankshaft pulley, near the tensioner.

What does service engine soon mean on Pontiac Grand Am?

Service engine soon means there is a problem with the emissions system. Usually it just means the gas cap isn’t on correctly, but it could be a bigger problem. I once had to have the O2 sensors replaced. 7 people found this helpful.

Where is the water pump located on a 1999 Chevy Malibu?

Locate the water pump located to the left of the engine, directly below the exhaust manifold, and use pliers to detach the hoses from the water pump by pressing the wire hose clamps together with pliers and pulling the hose off with your hands.

How much is a water pump for a 2004 Pontiac Grand Am?

2004 Pontiac Grand Am Water Pump – from $11.49+ | AutoZone.com.

How much is a water pump for a 2004 Grand Prix?

2004 Pontiac Grand Prix Water Pump – from $35.99+ | AutoZone.com.

How do you change a water pump on a 2001 Pontiac Aztek?

Drain the cooling system until the coolant is below the level of the water pump. Remove the drive belt guard. Loosen the water pump pulley bolts. Remove the drive belt….

1. Install the water pump gasket.
2. Install the water pump. Notice: Refer to Fastener Notice in Service Precautions.
3. Install the water pump bolts.

Why does my service vehicle light on?

The service vehicle light indicates that the car may be malfunctioning in other areas and it is usually found along with another indicator light that would typically give away what the malfunction is. It also indicates that your car may be due for routine maintenance.

Can low oil cause service engine soon light?

Low oil pressure is a common cause of a check engine light turning on, and it can seriously interfere with your car’s performance. Usually, if this is the case, your oil light will also appear. In any case, low enough oil pressure will disable your vehicle, so get this repaired immediately.

How much is a water pump for a 1999 Chevy Malibu?

We currently carry 5 Water Pump products to choose from for your 1999 Chevrolet Malibu, and our inventory prices range from as little as $33.99 up to $59.63.

How much is a water pump for a Chevy Malibu?

Chevrolet Malibu Water Pump Replacement Cost Estimate. The average cost for a Chevrolet Malibu water pump replacement is between $549 and $605. Labor costs are estimated between $216 and $273 while parts are priced at $332.

How to tell if a car’s water pump needs replacement?

How to Tell if a Car’s Water Pump Needs Replacement. Your car’s water pump is an important part of your vehicle. It is the part that continually pumps coolant to your vehicle’s engine so that it doesn’t overheat.

Where is the crank sensor located on a GM 2.2 liter?

Loading comments… The crank sensor is located on the side of the engine block, front, under the intake manifold area, near the oil filter housing. Enter text right here! Displayed next to your comments. Not displayed publicly. If you have a website, link to it here. Posting anonymously. © Copyright 2006 – 2020. JRKAZ,Inc. 7. EVAP Purge Solenoid

Who is the best mechanic for car water pump?

Rocco Lovetere is a Master Mechanic at Rocco’s Mobile Auto Repair in California, which he owns with his family. He is an ASE Certified Automotive technician and has worked in automotive repair since 1999. Your car’s water pump is an important part of your vehicle.

Where is the water pump located on a Pontiac?

The Pontiac car is a compact vehicle, so a number of parts and components are installed within close proximity. The water pump on the Pontiac car is connected to the thermostat housing, so you must work with both of these parts to replace the water pump.

How do you mount a water pump on an engine?

Clean the mounting surface on the engine with a screwdriver and a rag. Line the water pump-mounting surface with a thin layer of RTV silicone onto the water pump. Place the gasket on the water pump and press it into the silicone. Install the water pump and tighten the retaining bolts to 19 foot-pounds of torque.

How do you remove a water pump from a car?

Put the nut back onto the stud, so you don’t lose it. Remove the alternator retaining bolts, alternator and alternator bracket with the appropriate socket. Remove the water pump pulley bolts, then remove the pulley. Remove the water pump mounting bolts with the appropriate socket, then remove the water pump with from the engine.

Where is the access cover on a water pump?

Unbolt and remove the water pump’s access cover, located to the left of the drivebelt tensioner. Connect a holding tool (the exact tool is named J-43651 at auto service departments) to the water pump sprocket, and make sure the sprocket can’t move. Remove the bolts connecting the pump to the sprocket with a wrench.