Where is the alternator on a Cutlass Supreme?
Park your Cutlass Supreme in an open work area and pop the hood open. Use a combination wrench or socket wrench to remove the negative battery terminal cable. Locate the alternator, which should be bolted to the top left of the engine.
How does the Oldsmobile Cutlass Supreme charge the battery?
The alternator in your Oldsmobile Cutlass Supreme charges the battery as you drive so you won’t have to jump-start the car every time you start it and so the ignition system does not drain the battery.
How do you remove an alternator from a car?
Reach behind the alternator with a small 10mm wrench to loosen and remove the electrical connector found on the backside. Remove the alternator belt, paying special attention to how it is attached, then remove the second mounting bolt and pull the alternator out of the engine compartment.
How can I tell if a new alternator is the same as the old one?
Check the new alternator against the old one to be certain that the mount points and electrical connector are the same. If the alternators do not appear to be identical, return to the parts store to retrieve the correct alternator for your vehicle. Use a small 10mm wrench to connect the electrical wire to the rear of the new alternator.
Park your Cutlass Supreme in an open work area and pop the hood open. Use a combination wrench or socket wrench to remove the negative battery terminal cable. Locate the alternator, which should be bolted to the top left of the engine.
The alternator in your Oldsmobile Cutlass Supreme charges the battery as you drive so you won’t have to jump-start the car every time you start it and so the ignition system does not drain the battery.
Reach behind the alternator with a small 10mm wrench to loosen and remove the electrical connector found on the backside. Remove the alternator belt, paying special attention to how it is attached, then remove the second mounting bolt and pull the alternator out of the engine compartment.
Check the new alternator against the old one to be certain that the mount points and electrical connector are the same. If the alternators do not appear to be identical, return to the parts store to retrieve the correct alternator for your vehicle. Use a small 10mm wrench to connect the electrical wire to the rear of the new alternator.
What to do if your alternator is not working?
If your alternator is not working properly, save time and money by changing your alternator at home instead of taking the car to a mechanic. Park your Cutlass Supreme in an open work area and pop the hood open. Use a combination wrench or socket wrench to remove the negative battery terminal cable.
What’s the best way to tighten an alternator?
Using a wedge or pry bar between the far side of the alternator and the mounting block, pull the alternator upward. This will tighten the belt and allow you to slide the second, rear-mounting bolt into place. Use a socket wrench or combination wrench to tighten the rear mounting bolt securely.
How do you install a one wire alternator?
One wire alternators eliminate the unsightly factory wiring harness and simplifies installation by using only one wire for charging. To install a 1-wire alternator, disconnect the positive battery cable, unbolt and remove the original alternator, install the new JEGS 1 -wire alternator and re-tension the drive belts.
If your alternator is not working properly, save time and money by changing your alternator at home instead of taking the car to a mechanic. Park your Cutlass Supreme in an open work area and pop the hood open. Use a combination wrench or socket wrench to remove the negative battery terminal cable.
How do you attach an alternator to a car?
Attach the alternator belt to the alternator, making certain to attach it the same way it was attached to the old alternator. Using a wedge or pry bar between the far side of the alternator and the mounting block, pull the alternator upward. This will tighten the belt and allow you to slide the second, rear-mounting bolt into place.
What’s the best way to remove and replace an alternator?
Follow these simple, step-by-step instructions for removing and installing an automobile alternator with common tools. Includes advice on the correct wiring as well as testing and troubleshooting tips. Sponsored by BBB Industries – makers of premium alternators and starters that meet or exceed OE form, fit and function. http://www.BBBind.com
How to download an Oldsmobile Cutlass repair manual?
Our most popular manual is the 1982-1996–Oldsmobile–Cutlass Ciera–6 Cylinders T 4.3L MFI Diesel OHV–31228204 . This (like all of our manuals) is available to download for free in PDF format. How to download a Oldsmobile Cutlass Repair Manual (for any year)
How do you attach an alternator to a belt?
Attach the alternator belt to the alternator, making certain to attach it the same way it was attached to the old alternator. Using a wedge or pry bar between the far side of the alternator and the mounting block, pull the alternator upward.
Attach the alternator belt to the alternator, making certain to attach it the same way it was attached to the old alternator. Using a wedge or pry bar between the far side of the alternator and the mounting block, pull the alternator upward.
Our most popular manual is the 1982-1996–Oldsmobile–Cutlass Ciera–6 Cylinders T 4.3L MFI Diesel OHV–31228204 . This (like all of our manuals) is available to download for free in PDF format. How to download a Oldsmobile Cutlass Repair Manual (for any year)
Where is the alternator fuse on a GM 3.8L?
Reconnect the negative battery cable, that you disconnected in ALTERNATOR TEST 2. Locate the alternator fuse, which will be located in the fuse box in the engine compartment. To find the exact location of this fuse, you’ll need to consult your owner’s manual or repair manual, since it every 3.8L GM model may have it in a different location.