Where is fuse for OBD port?

Where is fuse for OBD port?

It is located beneath the instrument panel somewhere between the left end of the instrument panel and 12 inches (300 mm) past the vehicle centerline.

How do I reset my OBD scanner?

How to Clear OBD-II Codes

  1. Hook an OBD-II scanner to the car’s diagnostic port. This outlet is on the driver’s side, under the dash and usually near the steering wheel.
  2. Turn the scanner on.
  3. Turn the car on.
  4. Wait for the trouble code to appear on the scanner. Press the “Clear” button on the scanner to clear the code.

How do I test my OBD port?

With a multimeter set to “ohms” check the resistance between these two terminals (the ignition must be in the off position / key removed) as shown. If there is 60 ohms (+/- 2 ohms) your vehicle is equipped with CAN communication and the gaugeART CAN OBD Link is compatible with your vehicle.

How can I get my Honda Accord code without a scanner?

Step by step to pull Honda codes without a scanner

  1. Turn off the vehicle.
  2. Open the metal clipper or the bobby pin until forming a “U” form.
  3. Find the diagnosis system in the Honda vehicle.
  4. Open the car part and find the connector for the diagnosis system.

How do you tell if OBD codes have been cleared?

If the MIL (yellow engine icon) turns off abruptly after 20 seconds, then you know the DTCs have been reset by the engine monitoring system and not by a scan tool or by disconnecting the battery.

Is there a wireless OBD scanner for a Honda?

At times stand-alone scanners just don’t cut it. Those are the times when a wireless tool comes in handy. And if you own a Honda, there’s no other wireless OBD scanner that will be as helpful as the BlueDriver LSB2 Honda OBDII Scan Tool.

Which is the best OBD2 diagnostic scan tool?

BlueDriver is the Professional OBD2 Diagnostic Scan Tool trusted by mechanics and developed by Professional Engineers in North America. At times stand-alone scanners just don’t cut it.

Why is my ECU not connecting for OBD2 scan?

The next time u go try to get your codes read make sure they turn your key all the way so it’s positioned right before you turn the car on, might sound lame but every time I go someplace to get my codes read the people will turn the key to the first notch and then look stupid as they turn around and say, I can’t figure out why it’s not connecting.

How does the fixd work on an OBD scanner?

Codes, live data and freeze frame data. During the scan, the FIXD™ will display and clear generic codes in all the available systems. Just as important, it allows you to view freeze frame data so that you know when a code was registered. And you can also pull live sensor data to check the health and performance of various components.

What to do if the OBD II scanner doesn’t communicate with the vehicle?

What to do if the OBD II scanner doesn’t communicate with the vehicle. TEST 1: Connect the positive DMM lead to DLC pin 4 and the negative DMM lead to the negative battery terminal, using jumper wires if necessary. Do not connect to the body or chassis ground but to the battery terminal directly.

Why is my ECM not communicating with the OBD plug?

I traced all wires from the obd plug and made sure there were no My ECM is not communicating… My ECM is not communicating to with the OBD plug. I traced all wires from the obd plug and made sure there were no broken wires there and there is power going to a few wires on the plugs to the ecu.

Where does OBD 2 attach to kick panel?

Agreed on checking the fuses first – use a multimeter as you can’t always tell by looking at them. Per the diagram on page 22-89 of the service manual the HDS/OBD-II attaches to the MICU computer built into the drivers kick panel fuse box.

What causes a Honda HD to stop communicating?

Fuses 6, 7, and 21 in that fuse box are used by the MICU – if any are blown it could cause the HDS to stop communicating.