What tools are needed to replace a wheel bearing?

What Tools Do I Need To Replace A Wheel Bearing?

• A set of needle-nosed pliers.
• ratchet wrench with various sized sockets.
• flat-head screwdriver.
• jack.
• star wrench for loosening nuts on the wheel.

Can you replace wheel bearings without a press?

I’ve replaced bearings without either a puller or a press, it’s perfectly doable, although a bearing insertion set does make things much easier. These are cheap and you can get them off the internet.

Is changing a wheel bearing easy?

Is it easy to replace a wheel bearing at home? Replacing a wheel bearing that comes as an assembly with the hub and bolts to the spindle or steering knuckle is not very difficult if you have proper skills, tools and the manual. Of course, the large axle nut is very tight and can be difficult to remove.

How long does it take to change a wheel bearing assembly?

Rear wheel drive, tapered roller bearing: about 15-45 minutes; wear gloves or spend another 10 minutes washing grease off your hands. Front wheel drive with pressed on bearing: 30–120 minutes depending on whether it can be pulled off and pressed in with a specialty tool.

Can I replace a wheel bearing myself?

Changing your own wheel bearings is considered an intermediate job that can be done at home, but will need some speciality mechanic tools. Be sure to obtain your vehicle’s service manual and identify the type of wheel bearing your vehicle is equipped with before you begin the repair.

Is it OK to replace just one wheel bearing?

It’s usually safe to replace only one bearing that’s been damaged by a curb or pothole. If the bearings are simply worn, think hard about doing both sides at the same time. You also may be able to save some labor costs if your brake rotors and pads could use replacing at the same time.

What happens if you don’t fix a wheel bearing?

Ultimate damage: If you don’t replace a damaged wheel bearing before it fails completely, the wheel will completely seize up. If this happens while you’re driving, the results can be catastrophic.

Can your wheel fall off if you have a bad wheel bearing?

A: A bad wheel bearing can cause several potentially dangerous situations, starting with your vehicle not being as responsive as it should be. Last, but not least, your wheel can fall off completely while driving, as the bearing is an essential part of keeping the wheel attached to your car.

What happens if you don’t fix wheel bearings?

How do you change wheel bearings on a car?

To change wheel bearings, start by lifting the wheel up on a jack, unscrewing the lug nuts, and taking the wheel off. Then, remove the brake caliper, the dust cover over the rotor, and the cotter pin and castle nut behind the dust cover. Next, pull the rotor off, remove the old hub, and take apart the hub assembly to access the wheel bearings.

Where to put wheel chocks when changing wheel bearings?

For example, you would place wheel chocks behind the rear tires if you are fixing a front wheel bearing and behind the front tires if you are working on a rear wheel. Loosen the lug nuts and lift the wheel using a jack. For proper access to the internal components of the wheel whose bearings you’re replacing, you’ll need to elevate the wheel.

What do I need to replace front wheel?

When the tie rod end and lower ball joint are removed you can rotate and swing out the steering knuckle to remove it from the drive axle. You can then remove the E-14 bolts. I hit the hub assembly flange (the one with the lug nut studs) with a large hammer to drive it out of the steering knuckle, since the bearing was no longer good.

Where are the bearings located in the wheel?

Usually located in the wheel’s hub, rotor, or brake drum, bearings help the wheel rotate smoothly when the vehicle moves. If you notice a humming or whirring noise while you are driving or your ABS light turns on, it may be time to change your bearings.

When to replace wheel bearings on a Chevy Silverado?

Bad wheels bearings can cause your tires to wear irregularly. Prevent this by replacing the bearings; learn how to here. This article applies to the Chevrolet Silverado 1500 (1996-2006). It’s very important to replace wheel bearings when they begin to fail as they can cause a few different problems that can be both costly and dangerous.

How do you replace the front wheel on a Chevy Silverado?

Hammer the back of the assembly. Remove the 33mm nut again and then pull the hub assembly off. Remove the triangle shaped backing plate from the back of the assembly; you’ll be reusing this. Install the backing plate onto the new hub assembly; it just slides on.

Can a bad wheel bearings cause tires to wear irregularly?

Bad wheels bearings can cause your tires to wear irregularly. Prevent this by replacing the bearings; learn how to here. This article applies to the Chevrolet Silverado 1500 (1996-2006).