What to do if your odometer is not working?

What to do if your odometer is not working?

To fix it, I “jumped” power from the row above at fuse #6 or 7 it was a blank “not used fuse” that only gives power when the ignition is on. (tested with light) I simply stripped both ends of a short wire and jumped it from top terminal to top terminal. Probelm solved…got my speedo, odom back, and brake n abs light off.

How do you reprogram the odometer on a Toyota?

Replace the speedometer board into the gauge housing and screw in the 5 screws at the back of the cluster. Replace the black bezel and wipe it from all finger-prints. Replace the clear cover. Reinstall the gauge cluster into the vehicle. Turn on the vehicle and check to make sure all the gauges work.

Where is the odometer value stored on a Toyota Solara?

It great for cluster swaps, as in my case I swapped a Lexus ES300 cluster into my Toyota Solara. Many cars store digital odometer values on the instrument cluster itself. It’s stored on a little chip on the speedometer circuit board; it’s called an EEPROM chip, usually of the 93C46, 93C56 or 93C66 variety.

Where do I find the odometer on my car?

You should have a “select/reset” knob up in the right hand corner of your dash that will allow you to click and scroll through the various displays such as instant fuel economy, odometer, trip meter, outside temperature. Be sure the vehicle is in park when doing this.

How does tampering with the odometer work?

This type of tampering is not like odometer rollback, the vehicle owner would just shut off the switch for a few months while driving so the mileage wouldn’t rack up, and if the driver need to see the speed of the vehicle at any time, that’s all they would have to do is turn the switch on for a few seconds, check their speed and then turn it off.

Replace the speedometer board into the gauge housing and screw in the 5 screws at the back of the cluster. Replace the black bezel and wipe it from all finger-prints. Replace the clear cover. Reinstall the gauge cluster into the vehicle. Turn on the vehicle and check to make sure all the gauges work.

It great for cluster swaps, as in my case I swapped a Lexus ES300 cluster into my Toyota Solara. Many cars store digital odometer values on the instrument cluster itself. It’s stored on a little chip on the speedometer circuit board; it’s called an EEPROM chip, usually of the 93C46, 93C56 or 93C66 variety.

What to do when your odometer has zero miles on it?

When a shop/garage has to replace a digital odometer, the replacement odometer sent from the factory has zero mileage on it, so the odometer needs to be sent out to a professional speedometer facility to have the mileage from the old odometer transferred onto the new odometer. The process is not complex, but it is time consuming.

If only your odometer is not working, then the dash cluster may be the culprit. Should you need to replace it, here are the instructions for replacing the dash cluster. Start by parking your vehicle on a level surface and setting the parking brake. * Turn the ignition to the ‘on’ position.

When to suspect odometer has been tampered with?

So if you happen to see gouge marks around the instrument cluster, be sure to ask if the odometer has ever been changed out, don’t assume the odometer mileage has been tampered with because there are many reasons to remove the instrument cluster, and not just to get to the odometer.

Do you have to put an odometer replacement sticker on your car?

If a digital odometer is replaced legally, the mileage doesn’t have to be synced onto the new odometer, but the shop or garage doing the work will have to install an odometer replacement sticker somewhere very noticeable in the vehicle.

Where is the odometer located on a PRND321?

Carefully pry the board away from the instrument cluster – it is held in place only by the pins of the stepper motors (labelled on the image)… but BEWARE, there is another small wire harness on the right and side of the board. The last thing is to gain access to the back of the LCD panel.

Why is my odometer and message center not working?

If both the odometer and message center are not working, the problem is likely to be a fuse (both of these displays share the same fuse.)

Why is odometer tampering a big problem?

Odometer tampering is a huge problem when buying a used car and the reason is simple, lower mileage used cars sell better, and they’re worth more money. So what can you do as a consumer to protect yourself from odometer mileage tampering?

How do you repair an odometer on a car?

Lining up the pins of the stepper motors with their corresponding sockets on the PCB, push the board back onto the instrument cluster. Put pressure on the back of where the stepper motors are (see photo). Replace the back plastic cover of the instrument cluster, ensuring all clips are secured.

If all of your odometer gears check out, you can then test the odometer operation to see where the problem lies. To do this you should place a power drill, with an appropriately sized square drill bit, in to the speedometer cable opening and run the drill.

Can a broken Odometer be repaired on a Mercedes?

If you find that another problem exists, like broken teeth on one of the plastic gears, this guide will not be of use until you replace the gear and then test the odometer again to see if you also need to undertake this repair. No parts specified. You’ll need to begin by removing the instrument cluster from the car.

How does the odometer work on a Mercedes W123?

It is attached to a shaft that is responsible for turning the main odometer gear. This grey gear is the main odometer gear that turns the small plastic gears along the top of the odometer numbers. This is the other end of the shaft the brass gear is attached to. It is held in place by a tight fitting brass ring.

How does the speedometer and odometer work?

This is likely related to what is called a speed input/output shaft sensor which is a sensor mounted down on the transmission that monitors the speed of the output shaft of the transmission. This is relayed to your ECU which produces this information in your speedometer and odometer.

Why is my odometer and speedometer not working?

The speedomerter, odometer & mileage guages are not working. Have not experienced any other symptoms. Brakes are operating properly, have not received any warning/service lights other than tires need rotating. Was told by a mechanic that it’s the ABS System Sensor and was given the quote for a used one for $500 plus. Can you advise on this?

Is it possible to change the odometer display?

The odometer display can be just as easily changed by swapping clusters to one of a lower mileage. 3. This procedure requires disassembly of the cluster, and de-soldering of SMD components. Use care and caution when dealing with delicate components, and practice first on a spare cluster.

What kind of car can I reprogram my odometer?

The vehicle this was demonstrated on is a 2004 Honda Accord. YouTube Video: DIY Honda Odometer Reprogramming

Where is the odometer located on a Chevy?

The odometer is part of the instrument panel and connected to the speedometer. It is used to determine distance traveled and due to previous problems with individuals and dealerships disconnecting the odometer, it is a federal offense to tamper with it.

If only your odometer is not working, then the dash cluster may be the culprit. Should you need to replace it, here are the instructions for replacing the dash cluster. Start by parking your vehicle on a level surface and setting the parking brake. * Turn the ignition to the ‘on’ position.

What does it mean when your speedometer is not working?

If the oil pressure, coolant, charge, or gas gauge doesn’t work or works erratically, the problem is in the gauge, wiring, or sender. Speedometers are unique in that some of them use physical cables instead of sensors, so a speedometer not working can also indicate a broken cable or stripped gear.

How is the speedometer connected to the dash?

All other dash gauges are connected to sensors or sending units via wires, while your speedometer may utilize either a speed sensor or a physical cable. In vehicles that use cables, the speedometer is physically coupled to the transmission via a cable. The cable is usually square on both ends or square on one end and slotted on the other.

What does it mean when gauges in your car stop working?

But when the gauges in your car stop working, it’s not a situation you can safely ignore. When one gauge stops working, the problem may be in the gauge itself or a bad sensor, while all the gauges cutting out at the same time often indicates a blown fuse or a defective instrument cluster.

What to do if your shift selector light is not working?

1. Disconnect the wiring connector from the original transmission mounted PNP switch. 2. Connect the new switch to the wiring connector. 3. Return to Step #4 above and observe the display as you rotate the switch. If all positions indicate properly, refer to the Correction section below.

Where is the odometer located on a Chevy?

The odometer is part of the instrument panel and connected to the speedometer. It is used to determine distance traveled and due to previous problems with individuals and dealerships disconnecting the odometer, it is a federal offense to tamper with it.

Where is the shift selector inticator light located?

If not, inspect the serial data circuit, CKT 2470 (Yellow wire), between the TCM and Splice Pack 205. Specifically inspect connector C106, a five terminal connector located below the left side underhood bussed electrical center, directly beneath the red battery cable terminal connection.

Why does the odometer on my Car Stop Spinning?

But the plastic gears that turn an analog odometer have a tendency to break, which causes the odometer to stop spinning. The good news is that this is an easy fix, as demonstrated by YouTuber Chris Fix.

Why does my odometer fail on my Corvette?

Many odometers fail because the gears that drive them fail. Visit our sister site SpeedometerGears.com to order them. We also have Corvette odometers for 1953 to 1983 Corvette speedometer repair for sale and worms gears.

Where can I get a corvette speedometer repaired?

Visit our sister site SpeedometerGears.com to order them. We also have Corvette odometers for 1953 to 1983 Corvette speedometer repair for sale and worms gears. Call 1-800-572-2880 for help selecting and ordering those. Odometer may count the mileage incorrectly if the tire size is changed.

What should I do if my odometer is not working?

The good news is that this is an easy fix, as demonstrated by YouTuber Chris Fix. If both your odometer and speedometer are not working, then it’s likely your speed sensor needs to be replaced.

But the plastic gears that turn an analog odometer have a tendency to break, which causes the odometer to stop spinning. The good news is that this is an easy fix, as demonstrated by YouTuber Chris Fix.

What to do if your speedometer doesn’t work?

Replacing the bad speed sensor will solve this issue. Also, if speedometer in your Chevy stops working or reads erratically, test the cruise control out. The cruise control uses the same sensors as your speedometer. If the cruise is working and the check engine light is on, the problem is likely with the speedometer itself.

If the oil pressure, coolant, charge, or gas gauge doesn’t work or works erratically, the problem is in the gauge, wiring, or sender. Speedometers are unique in that some of them use physical cables instead of sensors, so a speedometer not working can also indicate a broken cable or stripped gear.

Why does my odometer stop spinning when I hit 200, 000 miles?

The only way you’ll know if your car hits the 200,000 mile mark is by having a functioning odometer. But the plastic gears that turn an analog odometer have a tendency to break, which causes the odometer to stop spinning. The good news is that this is an easy fix, as demonstrated by YouTuber Chris Fix.

Can a car be reset with a broken speedometer?

In the past, most mechanics ended up having to replace the speedometer head when a vehicle came in with a broken speedometer. Nowadays, there’s a possible reset procedure that can be used, and it can be done by most car owners right at home.

Where is the speedometer and odometer located?

If both your odometer and speedometer are not working, then it’s likely your speed sensor needs to be replaced. These are easily installed and located near the back of your transmission.

The only way you’ll know if your car hits the 200,000 mile mark is by having a functioning odometer. But the plastic gears that turn an analog odometer have a tendency to break, which causes the odometer to stop spinning. The good news is that this is an easy fix, as demonstrated by YouTuber Chris Fix.

Why did the battery die on my GT?

Was told by the shop that did repairs on the GT after it was rear ended 3.5 months ago that the battery had just died on them a day before, and that some of the gauges weren’t working. Thought that was strange that the dash was having issues.

How to repair the odometer on a GMC PRND321?

The instrument cluster is held in place by four (4) 7mm hex screws, one in each corner. Remove these. Tilt the instrument cluster forward carefully, and unlatch the large wire harness on the back. The instrument panel can now be removed. Remove the black panel on the back by loosening the clips.

1. Disconnect the wiring connector from the original transmission mounted PNP switch. 2. Connect the new switch to the wiring connector. 3. Return to Step #4 above and observe the display as you rotate the switch. If all positions indicate properly, refer to the Correction section below.

How to repair the odometer on a Chevy Avalanche?

In this Instructable, I will show you how to repair odometer/gear select (PRND321) LCD on your GM truck. In this case, mine is a ’02 Chevrolet Avalanche but this should apply to all GMT 800 series trucks within this age range. A common fault on ’99 – ’02 GM trucks was the permanent or intermittent failing of the odometer/gear select LCD.

Is there a way to repair a Ford odometer?

This video demonstrates the repair of a Ford odometer that was intermittently working. This repair was performed on a 2003 Ford F-150 pick-up truck but the process should be similar on other Ford truck and SUV models of the late 90’s through early-mid 2000’s.

Carefully pry the board away from the instrument cluster – it is held in place only by the pins of the stepper motors (labelled on the image)… but BEWARE, there is another small wire harness on the right and side of the board. The last thing is to gain access to the back of the LCD panel.

In this Instructable, I will show you how to repair odometer/gear select (PRND321) LCD on your GM truck. In this case, mine is a ’02 Chevrolet Avalanche but this should apply to all GMT 800 series trucks within this age range. A common fault on ’99 – ’02 GM trucks was the permanent or intermittent failing of the odometer/gear select LCD.

Why does the odometer go blank at night?

The same issue Traverse 2012, during the day in bright sunlight it goes almost blank, but in the night or shade it i ok, also sometimes when I smack above the dash it works for sometime and then goes back dark Just took our 2015 Traverse in for the same issue. They said it is the cluster and need to replace the entire instrument panel.

When does the odometer go on on a traverse?

So on our 2011 Traverse the display works at night with when the headlights are on but not during the day. If we cover the light sensor on the dash during the day after a few seconds the headlights, and odometer come on. It will stay on until we uncover the sensor and then goes out when the headlights go out.

Why is the night light on my computer not working?

Also, due to some other issue night light feature might be disabled for your computer, you might see its settings grayed out. The further night light settings don’t work as well. And from Action center the option is also not accessible. It is simply pretty straightforward, all you have to make sure Graphics drivers are installed.

What would cause the odometer light to go out?

It sounds like the instrument cluster i.e the odometer display may be wearing out. If you are only talking about the illumination for the odometer at night, then that may just be bulb that is getting old. Thanks for taking the time to respond.

Why does the speedometer work but not the odometer?

Proton Iswara’s (aeroback) dashboard, speedometer works but not the ODOMETER. For analogue dashboards, these normally work hand-in-hand or they don’t altogether. Initial guess was that the gear was broken, luckily it was a wrong guess.

So on our 2011 Traverse the display works at night with when the headlights are on but not during the day. If we cover the light sensor on the dash during the day after a few seconds the headlights, and odometer come on. It will stay on until we uncover the sensor and then goes out when the headlights go out.