What should I do if my tail light is not working?

Check the taillight bulbs. If the fuse and wiring look right, the bulbs themselves might be the problem. To check them, unscrew the taillight lenses from the outside using a screwdriver. If your lenses don’t have screws, open the trunk so you can access the lights from the inside.

When do you need to replace a tail light fuse?

On most new cars, the fuse would have to be removed to be checked due to the arrangement of the fuses. If the piece of metal inside the taillight fuse is intact, the fuse is still good. If the piece of metal looks broken or fractured, the fuse is blown and will need replacing.

Can a traffic officer cite you for a broken tail light?

For a straightforward light or fuse replacement, you can fix your tail lights yourself for a fraction of the price. You can be cited by a traffic officer if your car tail lights are not illuminating or broken, so don’t waste any time.

When to take a tail light bulb to the mechanic?

If the bulb is fine, your car may have a deeper electrical problem. If the fuse, taillight wires, and bulb are all in good shape, it’s time to take the car to the mechanic. When you remove a bulb for replacement, you should inspect the socket for burnt contacts and the tail lamp for burnt contacts or melted socket boards.

Preferred Procedure: Replace bulbs with manufacturer replacement bulbs. Tail light bulbs are replaced with incorrect bulb causing improper operation. If tail lights stay on continuously, the headlight/tail light switch or BCM has failed.

Why are the brake lights not working but the tail lights are?

Blown out light bulbs are the most common reason for why the brake lights not working but the tail lights are. Remove the screws from the bulb lens (which you can access through the trunk or see your vehicle repair manual to get the exact location). Push the bulbs and turn them counterclockwise to remove from the socket.

How can I tell if my tail lights have a fuse?

When you have located the fuse for the tail lights use a fuse tester to check the connection. If the tester lights up – your fuse is functioning fine. If it does not light up then, replace the fuse with another of the similar amperage and size. In many instances, you can see the break in the metal strip of the fuse.

How does a tail light control relay work?

Step 11 – A tail light control relay is used to help shoulder the electrical draw many bulbs can cause on a single circuit, this task is carried out by the BCM (body control module). The headlight/running light switch is used as the trigger circuit which sends a signal to activate the relay.

Why is the fuse not working on my tail lamp?

If you’re not getting +12 to the fuse, then the TAIL LAMP relay is not closing or is defective or there is a wiring/connector issue between the relay and the fuse. Another way to check the fuse (s) is to touch both sides of it with a test light or your meter set to volts.

Why are my tail lights not working but brake lights are working?

Burnt out light bulbs – The other reason your tail lights are not working but your headlights are maybe a blown bulb. When the filament inside the bulb breaks it cannot illuminate the gas enclosed within the glass cover. This burnt-out bulb does not affect the circuitry of the light system and it continues to function normally.

Is it dangerous to drive with broken tail lights?

So, driving with broken tail lights is very dangerous. Actually, people find out about their tail light problem when the police officer pulls them over. This is because the tail light malfunction is not that easy to spot. Usually, brake lights are the problem and the tail lights work just fine. But, sometimes it’s the opposite.

What’s the name of the bulb on the tail light?

Most tail lamps have stop lamp/turn indicator bulb(s), reverse lamp bulb, tail lamp bulbs, side marker bulb, and on some models a self standing turn indicator bulb. On cars where the brake and turn signal are sharing a bulb, when the bulb is burnt out, the turn signal indicator will flash faster than normal.

What to do if your tail light has come loose?

Open the trunk and take a look. You can see where the wires should connect in order for the electrical system to properly work. If a wire has come loose, reattach it. On most new cars, the wiring harness is located behind panels in the trunk and is not accessible without removing the panels. Check the taillight bulbs.

What kind of electrical problem does a Cadillac SRX have?

Wiring harness in steering column/steering wheel had a meltdown.Smoke was visable. The TPMS system was sending info intermitingly. The electrical part which recieves the tire pressures and sends to the DIC also controls the power doors. the part had corrosion on it ! replaced under extended warranty.In shop for 2 days.

How much does it cost to repair a Cadillac SRX?

The repair cost chart excludes repairs made under warranty, do-it-yourself repairs, and repair trips that include maintenance. 308-horsepower 3.6L V6 6-speed shiftable automatic FWD Known issue with OEM halogen projectors deteriorating and severely dimming the headlights.

Why are my brake lights not working but my tail lights are?

Damaged or disrupted wiring can cause tail lights not to work, but brake lights are. The two lightings use different wiring as each bulb has got its power supply. A recent accident at the tail end of your car can increase the likelihood of this problem.

Can a 2014 SRX be driven at night?

Just bought a wonderful condition 2014 SRX from a Caddy dealer who apparently never tried to drive the thing at night. I have absolutely no noticeable light output on the road from the normal headlights. They are visibly on but no illumination of the road. High beams work great.

How do you replace HID bulbs on a Cadillac?

I replaced my HID bulbs (upper large in the projector) from the backside without bumper removal. Passenger side need to remove air filter box. Have to uncouple air duct from engine intake, lift off cover, remove filter, unbolt screws in bottom of box, then remove lower portion of air box.

Which is brighter the SRX or the hid?

I inserted the HID bulbs into the projector housing on my Sky and Projector housing on the SRX. The light output on the Sky was much greater than the SRX. But the HID on the SRX was much brighter than the halogen on the other side of the SRX. Bright enough to probably be able to drive at night.

When to rotate the headlight switch for DRL?

In daylight, when you know the DRL are on, rotate the headlight switch from the auto position to the headlights on position and see what happens with the headlight intensity.

Where can I get parts for my Cadillac?

RockAuto ships auto parts and body parts from over 300 manufacturers to customers’ doors worldwide, all at warehouse prices. Easy to use parts catalog. CADILLAC Parts | RockAuto

Why would the tail lights not work?

Sometimes, pressing the brakes turns off the tail lights too and they don’t start working again until you let the brakes off. The possible reasons for brake lights not working but tail lights are: Blown out light bulbs are the most common reason for why the brake lights not working but the tail lights are.

Why are both my tail lights not working?

Possibly the most common reasons why tail lights are not working is because of the burned bulb. As we all know, every car’s light is manufactured and made out of the light bulbs. These lights are very similar to the house light bulbs and they also can burn or malfunction. Nov 17 2019

How do you replace tail light bulb?

Step 1: Open the lift gate. Step 2: Remove the two 10mm bolts. Step 3: Pop the tail light free from the pins on the side. Step 4: Disconnect the tail light electrical connector. Step 5: Remove the light bulb fixture assembly. Step 6: Replace the bulbs. Step 7: Reinstall the bulb assembly into the tail light.

Why do your brake lights work but not your tail lights?

The possible reasons for brake lights not working but tail lights are: Blown out light bulbs are the most common reason for why the brake lights not working but the tail lights are. Remove the screws from the bulb lens (which you can access through the trunk or see your vehicle repair manual to get the exact location).

Seems rather expensive when the old tail light assembly can be removed the same way and for a few bucks change the bulbs. Now this procedure costs (depending if you can do it yourself) an exorbitant amount for something that is not supposed to fail and that GM will not replace if you are over 50,000 mi.

What to do if your HID light bulb is not working?

The easiest way to verify that your HID headlight capsule is bad is to carefully remove both bulbs and replace the one that doesn’t work with the one that does. If the known-good bulb fails to turn on when placed in the other socket, then you’re dealing with a more complicated issue.

What happens when both headlights stop working at the same time?

You may destroy, or drastically shorten the life of, your good bulb. When both headlights stop working at the same time, the bulbs usually aren’t at fault. The main exception is when one headlight burns out first, goes unnoticed for some time, and then the other bulb also fails.

Why are my headlights not working in high beam?

If just one bulb fails to work in either high beam mode or low beam mode, it may be the bulb. Most headlight failures that are limited to just high or low beams are related to a relay or the high beam control switch.

Why are my tail lights still not working?

I Replaced the Light Bulb but the Tail Lights Still Don’t Work. Part of the series: Maintaining a Car’s Electrical System. If your tail lights won’t come on even after replacing a light bulb, this can be because of a few different things.

When do the tail lights and brake lights come on?

The taillights come on when your headlights are on or your parking brake is engaged. The brake lights turn on when you apply pressure on the brakes. In most automobiles, the taillights are red while the brake lights are a brighter, more luminous red. The rear lights are controlled by the same switch as the headlights.

How much does it cost to replace a damaged tail light?

If you were ever upset that the tail-light of your car is damaged because someone else has bumped into your car, and now you need to spend 100 Euro for replacing it, than here is an alternative that is not only very cheap, but is also more environment friendly because it reduces our global footprint. Loading…

Where is the ground connection for the brake and tail lights?

Locate the ground connection for the brake and tail lights. This will require you to remove the trim panels in some car trunks, which you can in some cases accomplish with a Phillips-head screwdriver or a small socket. The method will depend on the make of the car. Remove the screw holding the ground connector to the car body.

What should I do if my turn signal is not working?

A bolt or unpainted metal bracket will do. Then touch the socket contacts with your test light tip and have your assistant operate the turn lights. The test light should flash. If it does, check the ground connection at the socket.

How do you fix a bad ground wire for brake lights?

Repairing the connection is a project that is well within the range of the do-it-yourselfer. Locate the ground connection for the brake and tail lights. This will require you to remove the trim panels in some car trunks, which you can in some cases accomplish with a Phillips-head screwdriver or a small socket.

How do you repair a bad tail light wire?

Cut the wire off, leaving enough wire still connected to the socket to splice onto the new 16 gauge wire using another butt connector. Tape the connections very securely. This will help prevent corrosion which will reduce the voltage to the light. Turn the parking lights back on the test the repair.

Why are my lights not grounded in my trailer?

It sounds like you have an insufficient ground. It is enough to run the signals individually, but when you fire up the running lights, there is not a good enough ground. Check the ground wire at the trailer connector. Make sure each light is properly grounded. Some are stud grounded on the mounting hardware, others have ground wires.

How do you change the headlight on a Nissan pickup?

Changing your Nissan Pickup’s headlight is a no brainer. Just make sure that you know what kind of bulbs you are going to need. Once you’re sure, just pop up the hood and locate the bulb holder and change the bulb. You may need to unfasten some latches, but overall, it’s pretty easy as 1-2-3.

What causes brake lights to not work but tail lights do?

5 Causes of Brake Lights Don’t Work But Tail Lights Do 1 Bad Light Bulbs 2 Bad Brake Light Switch 3 Broken fuse or fuse box 4 Bad sockets and connectors 5 Broken wire More …

What kind of car has no tail lights?

I have a 1992 Acura Integra and the strangest thing happened yesterday. The tail lights turned on all by themselves and would not turn off. The car is seldom used (keeping it for my boys that will be driving soon) and was parked at the time.

What do the tail lights on a car do?

The taillights are concealed units having light bulbs or LED; which help the driver to take a turn to the right or left smoothly. How many times we have seen a car in an accident, and noticed it had no taillights?

What to do if your tail light is not working?

Now, if you are certain that your tail light is not working, and the light bulb is just fine, it is recommendable to take your car to mechanics. Simply speaking, every time there is an electrical problem with the car, it is highly recommendable to let the professionals handle it.

What are tail lights and where are they located?

Tail Lights. What are tail lights and where are they located? Tail lights are also known as taillights, tail lamps, taillamps, brake lights, brake lamps, rear lights, or rear lamps. The funny thing about them is that not all tail lights are considered brake lights, but all brake lights are considered tail lights.

5 Causes of Brake Lights Don’t Work But Tail Lights Do 1 Bad Light Bulbs 2 Bad Brake Light Switch 3 Broken fuse or fuse box 4 Bad sockets and connectors 5 Broken wire More

How are the tail lights and dash lights connected?

Tail lights and dash lights are connected through the tail light (and/or brake light) fuse. When the dashboard goes dark you know you are driving without tail lights. [ [Image:Fix Dashboard Lights That Won’t Light Step 2 Version 3.jpg|center]]

When do you need to replace tail light bulbs?

You need to replace bulbs if they have got darkened or the filaments are blown. Choose the new bulbs of the same type and wattage. In most European cars, the same bulb does the job of the tail and brake lighting. However, it has double filaments, allowing one set still working while the other set is burnt.

Is it dangerous to have a broken tail light?

As we all know, tail lights are quite important and crucial on any vehicle. So, driving with broken tail lights is very dangerous. Actually, people find out about their tail light problem when the police officer pulls them over. This is because the tail light malfunction is not that easy to spot.

Can you use glass cleaner to fix tail lights?

Do not use glass cleaner to clean the area because the ammonia in the glass cleaner will cause the tape not to stick as well as it should. The last wipe with rubbing alcohol will remove most of the impurities and leave a clean surface. Measure the size of the crack and cut the tape slightly larger than the damage of the lens.

Why are my tail lights not working on my Chevy C / K 1500?

Also, check your ground wire connections in the wiring harness as well. These problems can often result from the installation of after market trailer wiring harnesses where improper connections have allowed corrosion to enter the wire at the splice points. 30 people found this helpful. Check the ground Wire under the bed in the back.

How to change the tail light on a 1998 Toyota Camry?

This video demonstrates how to change a burnt out taillight bulb on your 1998 Toyota Camry. Some of the other bulbs in the tail light cluster such as the brake light or turn signal may also function as the tail light in your Camry.

How long does a tail light bulb last?

The tail light housing will usually last the life of the vehicle, but external factors can affect this. Tail light bulbs also have a chance of lasting the life of the vehicle. Many manufacturers claim LED bulbs can last up to 25,000-50,000 hours, but that’s not always a given. Incandescent can last from 750-1,000 hours.

Why is my tail light not working properly?

Common causes for this condition is a loose fitting bulb inside the socket. To test for this condition expose the tail light bulb in question. Next, switch the tail lights on and move the bulb around slightly in the socket. If the bulb flickers tighten the socket or replace the bulb/socket to regain proper operation.

What to do when your tail light goes out?

While the tail light bulb is installed, touch a grounded test light to the outer ring or ground wire of the bulb socket. If the bulb brightness increases, the bulb socket ground has gone open and must be cleaned or repaired-replaced.

Where did I Buy my 2014 Audi Q7?

We bought our 2014 4.2 TDI V8 as a low Klm Demo from Audi Sydney, where both the pre and post sales service was excellent. 5 years and 142,000 Klms later (and with a little sadness) we said goodbye to the vehicle a few weeks ago (as a trade on a new Q5).

Are there any problems with the Audi Q7?

Numerous problems since buying 2015 model. Audi Five Dock unable to fix problems despite car been back to them approx 20 times since we had it. Sunroof squeaking and finally replaced.

How many L / 100 does Audi Q7 have?

We averaged 10.5 L/100 mixed and around 8L/100 from Sydney to Coffs on regular trips great for the size / performance. The car was tight from day 1 to day 1832, not a squeak or rattle or unusual noise anywhere.

Why are the interior lights not working on my car?

If your interior lights used to stay on for a while after closing your doors, then there is probably some kind of timer module in the circuit. So if your fuses are good, the door jamb switch checks out okay, and everything else seems to be in working order, you may be dealing with a more complex problem.

What to do if your dashboard light does not work?

A blown fuse can disable the vehicle’s dashboard light. The fuse box may be under the hood, or near the floor, near the brake pedal, or there may be two fuse boxes in both places. Refer to the diagram on the fuse box cover to locate the correct fuse. Replace the dashboard light fuse if necessary. Note: also check if the tail lights are working.

Is it possible to fix a bad trailer light?

Some problems, such as a burned-out bulb or a bad trailer light ground wire, can be a snap to fix—others can be a real pain to diagnose and repair. Follow the steps in our photo sequence to keep your trailer lights in tiptop condition. Complete DIY projects like a pro! Sign up for our newsletter!

Why does my tail light bulb keep flickering?

Step 17 – Flickering or flashing lights occur because a power or ground source is being disconnected momentarily and then reconnected. Common causes for this condition is a loose fitting bulb inside the socket. To test for this condition expose the tail light bulb in question.

No matter if only one of the lights in the fixture is not working correctly, the assembly needs to be examined and brought back to optimal condition. This way, you and your passengers can rest assured that you are driving safely and communicating well with other drivers on the road.

Where can I buy a tail light assembly?

If you are in the market for the best tail light assemblies for cars and trucks, look no further. AutoZone has a wide selection of tail light assemblies for specific vehicles to get your lights shining once again. Old Lights Wearing Out?

Why do we need AutoZone tail light assembly?

We at AutoZone are proud to offer tail light assemblies that conform to United States federal motor vehicle safety standards as well as Department of Transportation requirements because we care about your safety on the road.

Can a tail light be damaged in an accident?

Touch device users, explore by touch or with swipe gestures. When autocomplete results are available use up and down arrows to review and enter to select. Touch device users, explore by touch or with swipe gestures. If you’re in a rear-end accident, your tail light can be easily damaged.

What should I do if my dash lights are not working?

Normal operation is ground when off then positive when dash lights are on (voltage varied to dim the lights). My parking fuse kept blowing anytime the auto lights turned on the dash lighting. Also try a 20a fuse over a 15.

What’s the difference between Dash, tail and park lights?

(Not my problem, and I don’t let my battery get corroded!) mrmooney, good idea, tried it right after I checked the fuses. kbro had the right idea. 7jimmy7 nailed it first, with Michael following him up. The only thing that my dash, tail, and park lights have in common is the headlight switch.

What to do when your dash lights don’t work?

If it’s okay, move on to the red/black terminal. With the combination light switch on, check to make sure there’s adequate battery voltage. The last terminal is the red one. Again, with the combination light switch on, check to see if the dash lights are illuminating as bright as possible. Figure 4. Dashboard brightness controller test.

Tail lights and dash lights are connected through the tail light (and/or brake light) fuse. When the dashboard goes dark you know you are driving without tail lights. Make certain to use the exact replacement dashboard light fuse to avoid the potential of electrical failure in your vehicle’s dashboard.

Why are the tail lights on when the car is off?

If the tail lights are on when the vehicle is off, there could be a few causes depending on the vehicle, including a broken brake light switch or brake light switch stopper, faulty trailer light plug, or a broken wiring harness. First, check if it’s the tail lights or the brake lights. Learn the difference of the two here.

How do you change a tail light bulb?

Insert the new light bulb and securely fasten the light bulb to the back of the tail light. Insert the tail light into the housing. Tighten all clips or bolts that hold the tail light onto the vehicle. Secure any electrical harnesses and reinstall any covers that were removed.

How do you replace a rear brake light bulb?

Follow the wires to the back of the light that you need to replace—that’s the bulb holder you want to unscrew, or, rather, pull out. It doesn’t actually unscrew; instead, you only turn it a quarter turn or so to unseat it and pull it out. Finally!

How long does it take to replace a tail light bulb?

It’s important to know what to expect with any car maintenance or repair job. Fortunately, tail light bulb replacement isn’t difficult and shouldn’t take you more than 45 minutes to an hour to complete. Be aware that newer models may be a little more complicated than older ones, as there will be more wires to disconnect.

How do you replace a brake light bulb?

Identify and remove the brake light socket. Twist and pull the socket to pop it out. Remove the bulb. On some vehicles, you have to twist and pull to get the bulb out, but in most vehicles the bulb can just be pulled out. Check to make sure the electrical contact where the bulb fits in the socket is not burned.

How do you replace fuse on tail lights?

Locate the fuse marked “tail lights” and use the fuse removal tool to pull the fuse out of the fuse block. Replace the old fuse with a new fuse of the proper rating (see your owner’s manual) by pushing the fuse with your fingers into the holes that the old fuse came out of.

Why are the tail lights on my Jeep not working?

If it is the tail lights that are inop there are some common problems associated with this model Jeep. The most common is the tail light sockets. They often melt the housing they fit into and consequently lose ground. The only way to properly fix this is by replacing the entire taillight assembly” italic text”.

What should I do if my rear lights are not working?

Blown Fuse: As a first resort, a mechanic should expect the corresponding fuse for your rear lights. When a fuse blows, it prevents the circuit from completing, in this case preventing the rear lights from illuminating.

How do you replace a tail light fuse?

Insert the new bulb by inserting it into the area and turning it clockwise until it is securely in. Press on your brakes and see if your tail lights are working with the new bulb. If they are working, you can replace your tail light covers. If you are still having problems, a new fuse might be the answer. This is explained next.

How do you replace a tail light cover?

If they are working, you can replace your tail light covers. If you are still having problems, a new fuse might be the answer. This is explained next. Locate the control panel inside your vehicle. This houses all your fuses. Find the one that is labeled “tail lights,” and remove it from it’s area.

Why are the tail lights not working?

Tail lights do not work when the headlight switch is activated. As noted above, different automotive manufacturers have different tail lamp bulb configurations. In many cases when the lights don’t work when the headlight is turned on, it is caused by a burnt out or short circuited tail lamp bulb.

How to repair a broken tail light lens?

If the interior is rather bumpy or rough, use a cellophane tape. A tail light lens repair kit usually has a material inside to mend the damage. To activate the chemical process, you need to blend the ingredients, like an epoxy. After the mixture is complete you have to apply it in the soonest to make sure its effectiveness has not gone away.

Why are the tail lights on my maxima not working?

My 2007 Matrix tail light would not work. Fuse was okay and bulbs were new. The hardest part of the job was to find the fuse boxes and relay box (fuse box underneath hood, under driver side and relay behind glove box). I have a 1992 Nissan maxima my tail lights don’t work, I checked the fuses and the bulbs are good.

How to change the tail lights on a Pajero?

An error occurred. Please try again later. (Playback ID: Eq0YmNCO8ESF3GOi) An error occurred while retrieving sharing information. Please try again later.

How do you remove tail light from Dakota?

Fully open the Dakota’s tailgate. Locate the 2 torx screws on each side of the bed. Use the torx screwdriver to remove the screws. Keep them in a safe place for later installation. Pull the tail light assembly from the Dakota. Twist the lamp modules 1/4 turn counterclockwise to disconnect the assembly from the wiring.

When do I need to replace my tail light?

You should replace tail lights after signs of physical damage, yellowing or faded tail lenses, moisture build up, worn out looks, or burnt out internal circuit boards. It’s a good idea to replace tail lights immediately, as it’s a serious safety concern for you and the drivers around you.

Why are my tail light bulbs not working?

Moisture – Sometimes old tail lights will allow water inside, and this moisture is extremely difficult to get rid of. Moisture can shorten the life span of bulbs dramatically. Our brand new aftermarket replacement lights are the highest quality and won’t allow water inside.

What’s the difference between brake lights and tail lights?

Tail lights are also known as taillights, tail lamps, taillamps, brake lights, brake lamps, rear lights, or rear lamps. The funny thing about them is that not all tail lights are considered brake lights, but all brake lights are considered tail lights. Confused?

How to re-tint faded amber tail lights?

Funkmasterbrad on the DMCTalk forum has successfully used VANS Tail Light Spray to re-tint his faded amber tail lights, which had become completely clear after sitting in the desert sun for 25 years. He was able to simply remove the tail light assembly and spray the tint directly into the holes that the bulbs fit into.

Why are there so many blinking bike lights in Seattle?

Regulatory and enforcement agencies have certainly been blindsided, in Seattle as elsewhere in the United States. Absent any legal standards, light companies are in an arms race to produce the biggest, baddest bike lights.

Why are the tail lights red and the brake lights red?

In most automobiles, the taillights are red while the brake lights are a brighter, more luminous red. The rear lights are controlled by the same switch as the headlights. The power flows through a relay to the rear lights when the switch is turned on.

Why are my rear lights not working Inspection Service?

Rear lights are not working Inspection Service. Rear lights or tail lights, are an important safety feature on your vehicle, especially when driving at night or in bad weather. These lights let other drivers know where you are on the road and illuminate brighter to indicate when you are braking.

What kind of tail lights do you need?

All lighting components are direct replacements for a proper fit. Factory Replacement Tail Lights by K-Metal®. You need your tail lights to be functional for safe driving, so your vehicle and brake lights/turn signals can be seen by other drivers. Don’t drive with a damaged or non-functional tail… Factory Replacement Tail Lights by Hella®.

What happens when your tail lights are not working?

When the tail lights fail or do not function properly the car becomes a danger or hazard to self and others on the road. You may receive a ticket or citation from the traffic police. Blow fuse – The first thing the mechanics check is the fuse corresponding to the rear lights.

Why do my park lights stay on after I Turn Off the motor?

My park lights stay on after I shut off motor and park. It drained my battery and while recharging I heard a noise in the under hood fuse panel. I pulled out the fuse that was vibrating and the light went out but after placing the fuse back in the park lights refused to go out. So now I can not park the truck without pulling the fuse.

Why does the tail light on my Chevy Trailblazer not work?

Right rear tail light does not work when brake is applied. Have had this problem for several months, almost a year. I have changed the brake lights several times and the tail light still will not work. Intermittently tail lights malfunctioned this was due to a socket wire short that blew out the bulb .

Why does my tail light keep turning off?

If the tail lights turn off, the switch is likely faulty and the light plug assembly might need to be replaced. Sometimes the problem is from faulty wiring. Replacing a wiring harness is a possible DIY job that entails cutting the old connector off, stripping and twisting the wires and connecting the new switch with a splice connector.

What kind of problem does a GMC Trailblazer have?

A common problem on the mid sized General Motors SUV’s of the last decade (2002-2009 Chevrolet Trailblazer, GMC Envoy, Buick Ranier, Oldsmobile Bravada & Saab 97x), is irregular electrical malfunctions. Especially headlights that flicker and often go out with no warning and then come back on with no warning.

Is there a recall on a 2002 Chevrolet TrailBlazer?

The contact owns a 2002 Chevrolet Trailblazer. The contact received a recall notice for the exterior lighting:tail lights. On August 18, 2007, he arrived at the dealer to have the vehicle repaired. After servicing the vehicle for five hours, the contact was informed that the vehicle could not be repaired.

What to do if your dashboard light is not working?

Switch on your car and check to see whether your dashboard lights are working properly. If the dashboard lights are still not illuminating or if you donâ€™t feel comfortable attempting this process, enlist the services of a certified mechanic to replace any blown fuses and replace the light bulbs for you.

What to do if your tail lights are not working?

Take note that different states and countries have different rules when it comes to driving without tail lights or brake lights. Fines also vary, so you must check your lights before you drive. If your car tail lights are not working, fix this right away. If you cannot troubleshoot, ask a local garage repair center to help you out.

Why does the tail light stay on when the car is turned off?

There are many causes for tail light constantly staying on while the car is turned off: A broken brake light switch, damaged trailer light plug, faulty brake light switch stopper, broken wiring harness,… There are various reasons, however, you can check whether it is the brake lights or the tail lights to see which are the parts having problems.