What is the OBD code for an Acura check engine?

Table of Contents

What is the OBD code for an Acura check engine?

P1201Cylinder 1 Misfire – Compare possible causes/symptoms for this Acura check engine light code to the Generic OBD II code P0301 P1202Cylinder 2 Misfire – Compare possible causes/symptoms for this Acura check engine light code to the Generic OBD II code P0302

Where is the Check Engine light on an Acura?

The following procedure will allow you to read codes and reset the check engine light on Acura cars. Locate OBD-II Port under the dashboard on the driver’s side. This is a 16-pin port. All 1996 and newer ACURA vehicles have this port under the dashboard. Your browser does not support video tag.

Where is the DTC code on an Acura?

1. Connect SCS service connector special tool No. 07PAZ-0010100, or equivalent, to service check connector located under the passenger’s side of dash. 2. Turn the ignition on. 3. MIL will indicate DTC’s by outputting a number of flashes. Remember, these are manufacturer specific codes only.

How do you know if your car has a trouble code?

The LED will indicate diagnostic trouble codes (DTCs) by number of flashes. In the event of a PGM-FI system malfunction, the Check Engine lamp will light and stay On. When this condition occurs, proceed as follows: Using a jumper wire, connect terminals of service check connector.

What does the Acura check engine light mean?

Common symptoms that Acura owners notice when CEL comes on are: Check engine light flashing on and off. Check engine light, and TCS come on. Check engine light blinking. What does Acura check engine light mean? Acura check engine light (CEL) turns on to let you that the engine control unit (ECU) has detected a problem.

1. Connect SCS service connector special tool No. 07PAZ-0010100, or equivalent, to service check connector located under the passenger’s side of dash. 2. Turn the ignition on. 3. MIL will indicate DTC’s by outputting a number of flashes. Remember, these are manufacturer specific codes only.

What is the code for an Acura transaxle?

For example, 1 long blink, followed by 4 short blinks equals code 14. Four long blinks followed by five short blinks equals code 45. NOTE: Legend Models: If code 7 or 17 is stored and the S4 light on the transaxle indicator panel is also flashing, it may be necessary to diagnose the automatic transaxle control unit.

What does the ABS code 83-1 mean on my car?

In this case Code P2101 being set in the Engine computer (PCM) relating to the electronic throttle actuator has disabled the ABS system and set a code 83-1 to inform you of that.

What is the 83-1 code on a Honda Pilot?

Had a 83-1 code for the VSA indicators. Lots of rain Had a 83-1 code for the VSA indicators. Lots of rain yesterday. These indicators no longer showing. … read more Online Automotive Repair C… Vocational, Technical or Tra… I just read about the check engine code 83-1 (ABS) on a 07 Honda Pilot and what it means.

In this case Code P2101 being set in the Engine computer (PCM) relating to the electronic throttle actuator has disabled the ABS system and set a code 83-1 to inform you of that.

Had a 83-1 code for the VSA indicators. Lots of rain Had a 83-1 code for the VSA indicators. Lots of rain yesterday. These indicators no longer showing. … read more Online Automotive Repair C… Vocational, Technical or Tra… I just read about the check engine code 83-1 (ABS) on a 07 Honda Pilot and what it means.

What is the model of your Honda 83?

VSA light and 83-1 ECM/PCM Relationship Failure according to AutoZone guy with a handheld scanner? Mechanic’s Assistant: Just to clarify, what are the exact lights you’re talking about? VSA, a little upside down triangle, and the engine service light. Mechanic’s Assistant: What is the model of your ’83 Honda? Not an 83. It’s a 2008

What are the VSA light and 83-1 ECM / PCM?

VSA light and 83-1… VSA light and 83-1 ECM/PCM Relationship Failure according to AutoZone guy with a handheld scanner? Mechanic’s Assistant: Just to clarify, what are the exact lights you’re talking about? VSA, a little upside down triangle, and the engine service light.

How does the Acura MDX AWD system work?

How SH-AWD works: Acura’s AWD system explained. In a straight line, “overdriving” the rear wheels gives the MDX a more RWD feel than otherwise possible and in corners the system is capable of sending up to 70% of the power to the outside rear wheel helping the MDX’s cornering manners and masking the “plowing” tendencies normal in a front heavy car.

What kind of powertrain failure does an Acura MDX have?

ASE Certified, Ford Master… 77-01 Powertrain system failure. 2006 Acura MDX. Rsets all My Honda mrv 2004 has vtm4 and water light on?

What is code 77-1 powertrain system failure?

When I push the vmt-4 button for 4×4 it doesn’t do anything. If I put truck in reverse or 1 and push it comes on. … read more 2013 honda pilot 3.5 code 77-1 powertrain system failure. ATM-4 censor and engine light is on. Code77-1. 2007 Honda How much to fix? And how much for a complete tune up? … read more

Is there a VTM failure on a 2003 Honda MDX?

I have run a scan on a 2003 Honda MDX and got the following: 120-1 VTM-4 CTRL unit failure and 65-1 PCM Comm line failure. Both … read more mdx: rebuilt..Seems to be shifting, driving fine. Dealer says..module Hi, Have an 01 mdx just had trans rebuilt and am now getting check eng light and sometimes VTM light on dash.

What are the features of a 2010 Acura TL?

At the heart of the package is AcuraLink, a satellite system that provides real-time weather and traffic information with a convenient rerouting feature. Unlike many of its competitors, the 2010 Acura TL comes with most of today’s must-have features as standard equipment.

What kind of transmission does the Acura TL have?

From a performance driving perspective, the 2010 TL doesn’t offer as much pure fun as some of its competitors despite the addition of Acura’s sophisticated SH-AWD system. In a nod to enthusiast drivers, Acura offers a new six-speed manual transmission on all-wheel-drive models only.

Common symptoms that Acura owners notice when CEL comes on are: Check engine light flashing on and off. Check engine light, and TCS come on. Check engine light blinking. What does Acura check engine light mean? Acura check engine light (CEL) turns on to let you that the engine control unit (ECU) has detected a problem.

For example, 1 long blink, followed by 4 short blinks equals code 14. Four long blinks followed by five short blinks equals code 45. NOTE: Legend Models: If code 7 or 17 is stored and the S4 light on the transaxle indicator panel is also flashing, it may be necessary to diagnose the automatic transaxle control unit.

What is the diagnostic trouble code for rocker arm?

P2646 is a diagnostic trouble code (DTC) for “‘A’ Rocker Arm Actuator System Performance / Stuck Off Bank 1”.

What does it mean when your check engine light is blinking?

Check Engine Light Flashing. If your Acura check engine light is blinking it usually means there is an engine misfire. Fuel is not getting burned in the cylinder. In such cases, the engine will also shake noticeably. Do not drive an Acura for extended time if the check engine light is flashing.

The following procedure will allow you to read codes and reset the check engine light on Acura cars. Locate OBD-II Port under the dashboard on the driver’s side. This is a 16-pin port. All 1996 and newer ACURA vehicles have this port under the dashboard. Your browser does not support video tag.

Check Engine Light Flashing. If your Acura check engine light is blinking it usually means there is an engine misfire. Fuel is not getting burned in the cylinder. In such cases, the engine will also shake noticeably. Do not drive an Acura for extended time if the check engine light is flashing.

How to find trouble code on Acura 86-89?

To retrieve trouble codes, turn the ignition key to the “on” position with the engine off. 86-89 models: The ECU will flash many short blinks. The total number of blinks equals the code number. For example, 12 short blinks equals code 12, nine short blinks equals code 9, etc..

How do you know if your Acura has a trouble code?

On all models, turn ignition On and observe red LED on front or top of ECU. The LED will indicate diagnostic trouble codes (DTCs) by number of flashes. In the event of a PGM-FI system malfunction, the Check Engine lamp will light and stay On. When this condition occurs, proceed as follows:

Why is my Acura TL cranking but not starting?

There are a lot of issues that can cause your TL to crank, but not start. The engine needs air, fuel, and a spark in order to run. It is highly likely that if the engine is cranking, but not starting that it has thrown an OBDII code.

The LED will indicate diagnostic trouble codes (DTCs) by number of flashes. In the event of a PGM-FI system malfunction, the Check Engine lamp will light and stay On. When this condition occurs, proceed as follows: Using a jumper wire, connect terminals of service check connector.

How many airbags are in an Acura SRS?

Start Your Airbag Module Reset Order Today! 1-4 short circuited To 12 volt power or VSS. Driver’s Inflatable Air Bag Module 1-5 short circuited To Ground. Drivers Inflatable Air Bag Module

How does the maintenance minder work on an Acura?

Acura’s equipped with Maintenance Minder™ measures driving style, road conditions, and helps to notify you when scheduled maintenance is due. When you see the wrench, it’s time for Acura Genuine Service.

What are the trouble codes on an Acura MDX?

P0301-P0312: Cylinder Specific Misfire- These trouble codes correspond with a specific cylinder misfiring (cylinder number corresponds with its place in the firing order).

What does P0300 mean on an Acura MDX?

P0300: Random Multiple Misfire– This is one of the most common codes that is thrown when the engine is misfiring. It means that the engine has a misfire, but the computer can’t detect which cylinder that it’s coming from. This code is often thrown when there is a fuelissue, or a timing issue, and not just bad ignition components.

What are the symptoms of an Acura transmission malfunction?

Common symptoms that you experience when Acura transmission malfunctions: 1 Vibration while driving 2 Hesitation upon acceleration 3 Delayed shifting 4 Growling or grinding noise 5 Weak acceleration or no power 6 Transmission jerking 7 Check Engine Light on (P0700, P0730, P0740, P0780, P1768) 8 Erratic shifting 9 Loss of power while driving

Where do I find the cel code on my Acura MDX?

You can use a generic OBD-II scanner to retrieve CEL faults, but those codes will not be as helpful as the codes stored in the Powertrain Control Module (PCM) module (also known as transmission control unit). A multi-system diagnostic scanner that works on Acura will read fault codes from the PCM module.

What’s the phone number for the Acura recall?

For additional recall assistance, click the Ask Us button. If you are dissatisfied with your vehicle performance or have a product complaint, please contact Acura Client Relations at (800) 382-2238.

Is there a recall on the Acura MDX?

If you have questions regarding a recall, please contact Acura Automobile Customer Service at (888) 234-2138. Unable to retrieve recalls information at this time. There are no current safety recalls for this vehicle.

Where does the Acura TL 3.2tl come from?

The 3.2TL splits the difference in size and price between Acura’s aged Integra, a sporty compact sedan, and the 3.5RL, a larger luxury sedan. The TL is based on the front-wheel drive Honda Accord platform and is built in Marysville, Ohio, on the same assembly line as the Accord.

Is the Acura TL a good car to buy?

The 2000 Acura TL has not been tested. Like what you see? Find the best deal on a Acura TL today. There are for sale near you. Certified child passenger safety technicians conduct hands-on tests of a car’s Latch system and check the vehicle’s ability to accommodate different types of car seats.

Are there side impact airbags in the Acura TL?

For 2000, the TL gains standard side-impact airbags mounted in the front seatbacks. Seven sensors in the front passenger seat determine the size and position of the occupant. The side airbag is disabled if the sensors detect a small child.

To retrieve trouble codes, turn the ignition key to the “on” position with the engine off. 86-89 models: The ECU will flash many short blinks. The total number of blinks equals the code number. For example, 12 short blinks equals code 12, nine short blinks equals code 9, etc..

What causes a misfire on an Acura p1399?

If the engine speed fluctuates enough to cause the Crankshaft Position ( CKP) sensor signal to vary, the Engine Control Module ( ECM) can determine that a misfire is occurring and the Diagnostic Trouble Code (DTC) will set. Need more information on how to fix the P1399 ACURA code?

When did the Acura TL come out in the US?

Acura TL. Jump to navigation Jump to search. The Acura TL is a compact executive / entry-level luxury car that was manufactured by Acura. It was introduced in 1995 to replace the Acura Vigor and was badged for the Japanese-market from 1996 to 2000 as the Honda Inspire and from 1996 to 2004 as the Honda Saber.

Where is the V6 engine located on an Acura TL?

The V6 engine in the 3.2 TL was mounted in a front-rear, or longitudinal position. This contrasted with the more typical transverse engine mount style, and was intended to provide better weight distribution and reduce nose dive. The engine mount design resulted in an elongated hood for the first generation TL.

What kind of navigation system does Acura 2000 TL have?

The 2000 TL switched from a CD database to a DVD -based navigation system. The entire continental United States became accessible with the navigation system; it was possible to drive from one coast to the other with the new navigation system. This section needs additional citations for verification.

What’s the difference between an Acura TL and Saber?

The main difference between the two cars were the front grille; the Inspire and Saber were also available with a 2.5 L Honda J-series V6 exclusive to the Japanese market. The very first 1999 Acura TL (2G) rolled off the assembly line on August 4, 1998.

When did the Acura CL type’s come out?

In 2002, Honda Access America developed a performance package for the CL Type S, which was built in concert with tuning firm Comptech.

Are there any problems with the Acura CL?

Problems have been seen with the 2nd generation CL models equipped with automatic transmissions (manual transmission models are unaffected). Reports say that after an average of around 40,000 miles, the transmission experiences gear failures, such as downshifts, slipping, flaring and not shifting, and leaking.

Where can I find generic check engine light codes?

Welcome to our listing page for Generic Check Engine Light Codes. This is an all inclusive list intended to help you get not only a code definition, but also some information on what could cause these codes and what can be done to repair the related faults.

Where to find diagnostic code for Acura check engine light?

1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the glove compartment. The connector has a removable cover. 2. Turn the ignition on. 3. Follow scan tool manufacturer’s operating instructions to access the Diagnostic Trouble Codes (DTC’s).

Why does my Acura check engine light flash five times?

Acura check engine light may flash five times when you turn the key to position II but don’t start the car. This happened when the fault codes were cleared with an OBD2 scanner or if the battery was disconnected. It means that the emission systems are not checked by the ECU self-test, also known as the emission readiness test.

What to do if your check engine light is blinking?

Do not drive an Acura for an extended time if the check engine light is flashing. Driving with the check engine light blinking increases the risk of causing damage to the engine.

How often do you change the air cleaner in an Acura?

Inspect idle speed every 160,000 miles (256,000 km). Adjust the valves during services A, B, 1, 2, or 3 if they are noisy. * 2: If you drive in dusty conditions, replace the air cleaner element every 15,000 miles (24,000 km).

Why does my Honda Civic have a p0740 code?

Also, as was mentioned, on some vehicles, the code may set when the TCC’s performance is out of range due to a mechanical problem. Several Honda vehicles are prone to P0740 including the Honda Accord, Civic, Odyssey, Civic, and CR-V. Aside from Honda, users have also reported P0740 in Dodge, Jeep, Chevrolet, and Acura.

What does the DTC code p0740 stand for?

What Does the P0740 Code Mean? Diagnostic trouble code (DTC) P0740 stands for “Torque Converter Clutch Solenoid Circuit/Open Circuit Malfunction.” On most vehicles, it indicates that the control module perceives an electrical fault with the torque converter clutch solenoid or the solenoid’s circuit.

What happens when torque converter code p0740 is triggered?

You may experience shifting problems when code P0740 is triggered. If the TCC is stuck on, it may cause the vehicle to stall when coming to a stop. A TCC that isn’t engaging/disengaging properly can cause a shudder that’s felt at certain speeds. Failing to engage the torque converter clutch results in slippage that reduces fuel mileage.

What does the maintenance code mean on an Acura?

Once the information display number reduces from 100% (fresh oil) to 15% (dirty oil), a wrench-shaped light will appear on your dashboard, along with maintenance codes that indicate that your vehicle is due for servicing, giving you ample time to plan ahead to have your vehicle serviced.

What do the symbols on the Acura dashboard mean?

Car symbols, or dashboard lights, are a car service reminder. The Acura Maintenance Minder codes indicate when and what service your car needs. Average rating from 11,610 customers who received a Brake Pads Replacement.

What does fault code p0743 on OBD II mean?

What Does Code P0743 Mean? OBD II fault code P0743 is a generic code that is defined as “Torque converter clutch (TCC) solenoid –electrical”, and is set when the PCM (Powertrain Control Module) detects an abnormal voltage in the electrical control circuit of the TTC ( T orque C onverter C lutch) solenoid.

What causes a torque converter clutch code p0743?

Some common causes of code P0743 could include the following- Damaged, burnt, shorted, disconnected, or corroded wiring and/or connectors Defective TTC solenoid Dirty, contaminated, or degraded transmission fluid that prevents proper operation of the TTC solenoid. Failed or failing PCM or TCM.

How do I get my Acura navigation code?

You will be requested to provide your current number and zip code. Also, by providing an email address, a confirmation with the requested code will be sent to you for your records.

Where is the diagnostic port on an Acura?

To diagnose Acura transmission problems, it is recommended to use an OBD2 scanner for Acura Honda Transmission. Locate the diagnostic port under the dashboard on the driver’s side. This is a 16-pin port.

Is there a problem with my Acura TL V6?

Share it! The 1998-2014 Acura TL V6 may develop issues with the automatic transmission. Rough shifting may occur, and the “D4” light and check engine may begin to blink. The check engine light will also illuminate, and OBD trouble codes P0700, P0730, P0740, P0780, P1768 and/or P1768 will be stored in the computer.

Why does my Acura check engine light keep coming on?

When your Acura check engine light remains on, the problem could be something as simple a loose gas cap. It can also be an indication of a serious engine issue, a problem with the emission system or in some cases even an indication of a problem with the automatic transmission.