What does code 342 mean?

The PCM (powertrain control module) sets code P0342 when it detects that the camshaft position sensor circuit on engine bank 1 is sending a reading that’s erratic or otherwise outside the manufacturer’s settings. The PCM then illuminates the Check Engine light to alert the driver of the problem.

How do I fix code P0344?

What repairs can fix the P0344 code?

1. Replacing a weak or dead battery.
2. Replacing chafed, melted, or otherwise damaged wiring.
3. Cleaning electrical connections to the camshaft position sensor.
4. Replacing the camshaft position sensor.
5. Replacing the crankshaft position sensor.

How do I fix code P0336?

What repairs can fix the P0336 code?

1. Replacing a damaged reluctor wheel.
2. Repairing or replacing a damaged crankshaft position sensor wiring or circuitry.
3. Repairing or replacing damage or corrosion of the crankshaft position sensor connector.
4. Repairing or replacing the crankshaft position sensor wiring harness.

Where is camshaft position sensor A circuit Bank 1?

Of course, the CMP is located on the engine, usually somewhere on the cylinder head, so it transmits CMP data to the ECU using wires.

What is code P0348 mean?

camshaft position
What the P0348 code means. This code tells the PCM that the camshaft position is incorrect for the optimal performance of the vehicle. If the camshaft sensor detects a voltage reading that is more than 10% higher than the manufacturer’s specifications, the P0348 code will be stored.

What is the camshaft position sensor bank 1?

P0341 code refers to a problem with the camshaft position sensor (CMP) signal on Bank 1. Alternatively, if the engine employs a V configuration, the “A” typically refers to Bank 1’s intake camshaft. Finally, the “bank 1” in the P0341 code refers to the side of the engine where the number one cylinder is located.

What does a cam sensor do when it goes out?

Poor Drivability A failing camshaft position sensor begins losing its ability to quickly transfer data. Mismatched fuel delivery and ignition timing, even if off by a few milliseconds, will cause your vehicle to sputter, accelerate poorly, lack power, stall or even shut off.

How can you tell if the crankshaft position sensor is bad?

Symptoms of a Bad Crankshaft Position Sensor

1. Your Check Engine Light is Blinking.
2. It’s Difficult to Get Your Vehicle to Start.
3. Your Vehicle is Stalling and/or Backfiring.
4. The Engine is Making Your Vehicle Vibrate.

What is the code for a bad camshaft sensor?

P0340 is a diagnostic trouble code (DTC) for “Camshaft Position Sensor Circuit Malfunction”. This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation.

What can cause cam sensor code?

What are the Possible Causes of the P0340 Code?

• Failing or defective camshaft position sensor.
• Circuit problems (e.g., damaged wiring, loose connections)
• Errors in the powertrain control module (somewhat rare)
• Damaged camshaft position sensor reluctor wheel.
• Problems with internal engine timing components.

What does the p0342 code on the Check Engine light mean?

The PCM (powertrain control module) sets code P0342 when it detects that the camshaft position sensor circuit on engine bank 1 is sending a reading that’s erratic or otherwise outside the manufacturer’s settings. The PCM then illuminates the Check Engine light to alert the driver of the problem. What the P0342 code means

What causes a p0342 Chevy camshaft position sensor circuit low voltage?

Sometimes and in some models, low battery voltage or a weak starter can trigger a Camshaft Position Sensor code. The cost of diagnosing the P0342 CHEVROLET code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

What does the CPS code p0341 mean?

This P0341 code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor.

When does the PCM set the code p0342?

The PCM (powertrain control module) sets code P0342 when it detects that the camshaft position sensor circuit on engine bank 1 is sending a reading that’s erratic or otherwise outside the manufacturer’s settings. The PCM then illuminates the Check Engine light to alert the driver of the problem.

What does the trouble code p0342 stand for?

The automotive trouble code P0342 is one of several generic malfunction codes relating to the camshaft position sensor (CPS). Trouble codes P0335 through P0349 are all generic codes related to the CPS inferring different reasons for the failure. In this instance, code P0342 infers the sensor’s signal is to low, or not strong enough.

What to do if your camshaft position sensor says p0340?

Visually inspect the camshaft position sensor connector in search of corroded or broken connectors. Make any other repairs (if other codes are present) to make sure that other codes are not sources of the trouble code P0340. Check your camshaft position sensor’s voltage, ground, and signal readings with a multimeter.

What does the p0172 Chevrolet engine code mean?

Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. What does this mean? The cost to diagnose the P0172 CHEVROLET code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.

What is the diagnostic code for Camshaft Position Sensor low input?

P0342 is a diagnostic trouble code (DTC) for “Camshaft Position Sensor Circuit Low Input”. This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation. Our certified mobile mechanics can come to your home or office to perform the Check Engine Light diagnostic for $0.0.