How to troubleshoot an Acura TL headlight problem?

Table of Contents

How to troubleshoot an Acura TL headlight problem?

If the headlights are still not working, there may be an issue with the fuse. Locate the primary under-hood fuse box on the driver’s side. Remove the cover and locate the fuse numbered “3-2.” If the metal piece inside the fuse is broken, it will need to be replaced. Use the fuse puller to remove the fuse. Replace it with an identical 40A fuse.

How to check for pulsar failure on a Honda Element?

Check this link out – about 2/3rds the way down in mentions the “pulser” ring . . . old Honda/ Acura term but maybe it still applies . . . If you find a wheel-speed sensor code, check the wiring continuity between the sensor, connector and wiring harness. Sensor resistance can be checked with an ohmmeter at the sensor or through the harness.

What should the wheel speed sensor read on a 1992 Acura?

Refer to a manual for the exact specs, but as a rule the front sensors on the 1992 Acura applications should read 750 to 1,200 ohms, and the rear sensors 1,100 to 1,600 ohms. If a wheel-speed sensor’s resistance is within normal range, remove the sensor and inspect it for damage or metallic debris sticking to the tip.

What kind of sensor is on an Acura TL?

The sensors at the front of the engine are considered B2S1 and B2S2, respectively. It is stated on the forums to stay away from the Bosch generic sensors, as these don’t work well with the engine management on the TL.

Are there any recalls on the 2004 Acura TL?

Based on information received from our latest subscriber survey, our reliability history charts give you a rundown on how used vehicles are holding up in 17 potential trouble spots, ranging from the engine, transmission, and brakes to power equipment and the electrical system. The 2004 Acura TL has been recalled 6 times by NHTSA. View Recalls

Check this link out – about 2/3rds the way down in mentions the “pulser” ring . . . old Honda/ Acura term but maybe it still applies . . . If you find a wheel-speed sensor code, check the wiring continuity between the sensor, connector and wiring harness. Sensor resistance can be checked with an ohmmeter at the sensor or through the harness.

Refer to a manual for the exact specs, but as a rule the front sensors on the 1992 Acura applications should read 750 to 1,200 ohms, and the rear sensors 1,100 to 1,600 ohms. If a wheel-speed sensor’s resistance is within normal range, remove the sensor and inspect it for damage or metallic debris sticking to the tip.

Are there any problems with the 2002 Acura TL?

See all problems of the 2002 Acura TL . Since all headlights have been redesigned to have plastic covers rather than glass, the amount of light available for lighting the road has diminished with time as the plastic ages. I have seen some vehicles where the headlight covers are totally opaque.

How many Acura TL’s have been sold?

Also please check out the statistics and reliability analysis of Acura TL based on all problems reported for the TL. 2005 Acura Tl- parked winters, garaged, babied and all service completed at the Acura dealerships. Car has 141,000 on it and was near 50,000 when purchased (aspec package etc).

Where are the airbags on an Acura TL?

Car has 141,000 on it and was near 50,000 when purchased (aspec package etc). Car has developed cracks in the dashboard from the windshield to the instrument panel, across the center speaker and now directly on the indentation where the airbag is located on the passenger side.

Why are my Acura TL headlights not working?

The contact stated that the driver’s side headlights failed to illuminate while driving at night. Also, the passenger side headlight assembly retained steam. The vehicle was taken to joe rizza Acura (located at 8150 w 159th st, orland park, IL 60462, (708) 403-7770) where it was diagnosed that the headlight units needed to be replaced.

See all problems of the 2002 Acura TL . Since all headlights have been redesigned to have plastic covers rather than glass, the amount of light available for lighting the road has diminished with time as the plastic ages. I have seen some vehicles where the headlight covers are totally opaque.

Are there cracks in the dashboard of my Acura TL?

Car has developed cracks in the dashboard from the windshield to the instrument panel, across the center speaker and now directly on the indentation where the airbag is located on the passenger side. Reached out to Acura for assistance ( (attached)) and they said the car is too old and outside warranty to help me.

Also please check out the statistics and reliability analysis of Acura TL based on all problems reported for the TL. 2005 Acura Tl- parked winters, garaged, babied and all service completed at the Acura dealerships. Car has 141,000 on it and was near 50,000 when purchased (aspec package etc).

How many repair TRIPS does an Acura TL make?

Chart based on 400 repair trips. The repair cost chart excludes repairs made under warranty, do-it-yourself repairs, and repair trips that include maintenance. 280-horsepower 3.5L V6 6-speed shiftable automatic FWD

What causes an Acura TL battery to fail?

Honda uses denso from research. Car runs great now. With more electrical items on newer cars a dying or dead battery will overwork the alternator and can cause it to fail. Going fwd I will check battery health regularly. Replaced radio do too buttons freezing.

Where is the fuse box on an Acura TL?

286-horsepower 3.5L V6 5-speed shiftable automatic FWD Bottom of the black fuse box, which sits above the refill plug for the automatic transmission, disintegrated when touched. It was brittle like potato chips. Replaced “underhood fuse box bottom”

If the headlights are still not working, there may be an issue with the fuse. Locate the primary under-hood fuse box on the driver’s side. Remove the cover and locate the fuse numbered “3-2.” If the metal piece inside the fuse is broken, it will need to be replaced. Use the fuse puller to remove the fuse. Replace it with an identical 40A fuse.

How can I troubleshoot my hid headlight problem?

Here’s a way to troubleshoot HID headlight problems. But first, you have to understand how HID headlights work An HID ballast is a boosting transformer that converts battery voltage into the approximately 75 to 110 volts needed to maintain the arc. The ballast is designed to detect bulb shut down.

When does the hid headlight bulb shut off?

• HID headlight bulb shuts off after being on for a while. Shut off is sporadic and unpredictable but happens more and more often over the next 100 hours of operation. Swap the problem bulb to the opposite side.

Why do HID headlights not have black mask?

An “S” HID bulb is designed to fit in a projector-style headlight assembly. It does not have the black mask because projector headlights have a built-in internal shield to prevent glare.

What to do when both head lights stop working at the same time?

When that happens, the operational lifespan of your headlight capsule will be severely compromised, and the only fix is to replace the headlight assembly. When both headlights stop working at the same time, the bulbs usually aren’t at fault.

Why does one of the headlights on my car not work?

One headlight doesn’t work. This is usually caused by a burned out bulb. High intensity discharge (HID) headlights can also fail due to other associated components. Neither of the headlights work. Bulbs usually don’t burn out together, but it’s still important to rule that out by checking for power.

What to do if your HID light bulb is not working?

The easiest way to verify that your HID headlight capsule is bad is to carefully remove both bulbs and replace the one that doesn’t work with the one that does. If the known-good bulb fails to turn on when placed in the other socket, then you’re dealing with a more complicated issue.

When that happens, the operational lifespan of your headlight capsule will be severely compromised, and the only fix is to replace the headlight assembly. When both headlights stop working at the same time, the bulbs usually aren’t at fault.

Why are my headlights not working in high beam?

If just one bulb fails to work in either high beam mode or low beam mode, it may be the bulb. Most headlight failures that are limited to just high or low beams are related to a relay or the high beam control switch.

What happens when you turn on the headlights?

When you turn on your headlights, that switch activates a relay. That relay, in turn, actually provides the electrical connection between your headlight bulbs and the battery. Fuses are also involved in order to provide a sacrificial failure point to protect the rest of the wiring.

If just one bulb fails to work in either high beam mode or low beam mode, it may be the bulb. Most headlight failures that are limited to just high or low beams are related to a relay or the high beam control switch.

When you turn on your headlights, that switch activates a relay. That relay, in turn, actually provides the electrical connection between your headlight bulbs and the battery. Fuses are also involved in order to provide a sacrificial failure point to protect the rest of the wiring.

Why does my Acura TLX engine not start?

When there is no spark, the engine will not start. You’ll probably have a misfire related code such as P0300, P0301, etc….. Ignition issues can be caused by many things, including bad spark plugs, bad coil packs, bad plug wires, computer issues, and more. 3. Engine Timing

Why does my Acura MDX not start up?

As a battery ages, it’s “cranking amps” decrease, leaving it with a diminished capacity for starting the vehicle. When this happens, you’ll often hear the vehicle crank slowly, but not start. You can take your battery up to the local parts store, or even Wal-Mart, and have it tested to see if it is still holding a charge.

What causes an Acura TL to not start?

Acura TL: Engine Cranks → Won’t Start 1 Fuel Issues. If your TL isn’t getting enough fuel, or any fuel at all, it may have a bad fuel filter, bad fuel pump, or bad fuel injectors. 2 Ignition Issues. One of the biggest issues that causes a vehicle to crank but not start is ignition issues. 3 Engine Timing. 4 Security. 5 Other Issues.

What kind of reliability does Acura TL have?

The Reliability score is based on our latest subscriber survey of 2006 Acura TL owners. The owner comments describe problems respondents experienced with this vehicle.

Are there any recalls on the 2006 Acura TL?

Based on information received from our latest subscriber survey, our reliability history charts give you a rundown on how used vehicles are holding up in 17 potential trouble spots, ranging from the engine, transmission, and brakes to power equipment and the electrical system. The 2006 Acura TL has been recalled 6 times by NHTSA. View Recalls

As a battery ages, it’s “cranking amps” decrease, leaving it with a diminished capacity for starting the vehicle. When this happens, you’ll often hear the vehicle crank slowly, but not start. You can take your battery up to the local parts store, or even Wal-Mart, and have it tested to see if it is still holding a charge.

Do you need to replace both high and low beams?

Some vehicles use a single bulb for both high and low beams while others do not. If the high beam on the same side is also out, it may be one bulb. You do not need to purchase specific bulbs for each side, but identifying which is the blown out bulb will help you to replace it without having to start the vehicle again.

What should I do about my Acura TL headlight bulb?

Ensure the washer fluid cap is secured and that the pins and tab are well fixed. For safety purposes, avoid working on your low beam headlight bulbs as they have high voltage. Contact your Acura dealer to do it for you. Also, avoid touching your halogen bulbs or bumping them against anything.

How big is an Acura TL fog light?

Acura TL Headlight Bulb Size Chart 2014 Acura Tl Chart Bulb Number Fog Light Bulb Front H11 LED Fog Light Bulb Front H16 LED Headlight Bulb High Beam 9005 Headlight Bulb Low Beam D2S

Is it possible to fix a bad low beam headlight?

Fortunately, fixing a bad low beam is a straight forward process in the majority of vehicles that can be done by most people without just a few hand tools. If replacing your headlight bulb does not work, there may be an electrical issue in your vehicle that should be addressed by a professional. Identify a blown out bulb.

Is there any warranty on an Acura TL?

This is because there is no warranty included. Always double-check your Acura TL bulb sizes, wattages, and voltages. The information provided is for reference purposes only. The providers are not liable for any errors encountered within the bulb guide.

How to find all the Acura warning lights?

Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue). There are over 60 of them, so search carefully! Models examined include CL, ILX, MDX, NSX, RDX, RL, RLX, TL, TLX, TSX, and ZDX.

How do you remove the bulkhead cover from an Acura MDX?

Turn off the Acura’s engine. Open the hood. Remove the eight screws securing the front bulkhead cover and remove the front bulkhead cover from the vehicle. Pull lightly on the electrical connector at the rear of the headlamp assembly.

Where are the fuses for the Acura dash lights?

It’s is definitely of the fuse under the hood if you go and you look at your fuse box it’ll say small light fuse located inside the fuse box it will be a 15 amp fuse. Once replaced all your lights should come back on that were not working

Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue). There are over 60 of them, so search carefully! Models examined include CL, ILX, MDX, NSX, RDX, RL, RLX, TL, TLX, TSX, and ZDX.

Why are the lights on my dash not working?

Dash lights not working i replaced my stereo and the dash light stopped working. i had a shop look at to make sure the dimmer wasnt the problem and they checked everything to do with the stereo and dash. i also checked the connectors in the dash and there all connected. any ideas? Did you check all the fuses?

What does it mean when the Acura brake light comes on?

Have an auto mechanic diagnose your Acura braking system. If this light comes on, it means there is low oil pressure in the engine. Stop the vehicle as soon as possible and check the oil level. Add oil if the level is too low.

When does the Acura warning light come on?

The light also appears when the parking brake is applied. Be sure to release the parking brake before driving if the light appears while driving, press the brake pedal lightly to check the pressure.

What does the VSA light on an Acura mean?

During cornering, if the vehicle turns more or less than desired the VSA system help stabilizes the car. When driving on loose or slippery roads, the VSA system assists the driver to maintain it’s traction. If the indicator light illuminates, it indicates that there is a problem with the VSA system and has it checked by an Acura mechanic.

Why is my HID light not working on my Acura?

With such a long life, it is possible that you will never need a HID light replacement on your Acura. Sometimes there are other causes for a light bulb going out. Incorrect wiring and faulty sockets can be the cause of a light bulb not working.

How often do you need to replace Acura HID headlights?

You typically only need to replace the headlights on your Acura vehicle when a bulb goes out. HID headlights last for 2,000 to 3,000 hours which is equivalent to about 90,000 driving miles. With such a long life, it is possible that you will never need a HID light replacement on your Acura.

Where are the headlight closure relays located on a car?

Used in “flip-up” lights, which fold out of the body of the vehicle, headlight closure relays are essential for headlight operation. This relay is located in your main fuse box or panel.

One headlight doesn’t work. This is usually caused by a burned out bulb. High intensity discharge (HID) headlights can also fail due to other associated components. Neither of the headlights work. Bulbs usually don’t burn out together, but it’s still important to rule that out by checking for power.

Why are my high intensity discharge ( HID ) headlights not working?

High intensity discharge (HID) headlights can also fail due to other associated components. Neither of the headlights work. The cause: Burned out bulbs, or an issue with power or ground. The fix: Check for power and ground, and fix if necessary. Otherwise, replace the bulbs.

Why are the head and tail lights not working?

The on-board computer turns on the tail and headlights according to the light outside the car. If it is dawn or dusk the head and tail lights will come on by themselves. The light sensors also switch off the daytime lights in some latest models. When the sensor is dirty or damaged it cannot tell if it is dark or day outside.

What causes your car headlights to not turn off?

Some of the issues that can cause car headlights not to turn off include problems with a: 1 Headlight switch 2 Multifunction switch 3 Daytime running light module 4 Light sensor 5 Relay 6 Grounded wire More …

Flip the switch or turn the dial or knob up and see if the lights on your dash come on or get brighter. If adjusting the switch doesn’t work, you may have a blown fuse or bad lightbulb. Or, the entire switch may be faulty, in which case, have it replaced by a certified mechanic.