How to replace the power window motor on a Dodge Ram?
Replacing the power window motor in your Dodge Ram isn’t a difficult task and not too expensive. Keep reading and this article will guide you through the process. Use a Phillips screwdriver to remove one screw by the power window switch and another two in the door handle bucket.
How to fix a broken power window on a 1998 Dodge Dakota?
This automotive repair tutorial shows you how to fix a broken power window on a 1998 Dodge Dakota Sport 4×4 when it won’t go up or down. Even if you don’t know exactly what is causing your power window not to work, this video will show you how to diagnose and fix the problem in your Dodge Dakota 4×4 truck.
How do you install a new power window motor?
Install the new power window motor in place of the old one. Set the regulator back onto the door frame, and fasten the three black Phillips screws. Tighten the two black screws between the water shield and nut, then roll it back over the door. If necessary, apply a spray of adhesive or tape to help the water shield stick.
Replacing the power window motor in your Dodge Ram isn’t a difficult task and not too expensive. Keep reading and this article will guide you through the process. Use a Phillips screwdriver to remove one screw by the power window switch and another two in the door handle bucket.
How to fix power window on drivers door?
(2) Using an ohmmeter, Test driver door switch for If you do need a new window motor, or regulator, check these instructions out. WINDOW REGULATOR – POWER REMOVAL (1) Remove the watershield. (2) Remove door glass retaining clips and secure the window in the up position using masking tape or equivalent.
This automotive repair tutorial shows you how to fix a broken power window on a 1998 Dodge Dakota Sport 4×4 when it won’t go up or down. Even if you don’t know exactly what is causing your power window not to work, this video will show you how to diagnose and fix the problem in your Dodge Dakota 4×4 truck.
Install the new power window motor in place of the old one. Set the regulator back onto the door frame, and fasten the three black Phillips screws. Tighten the two black screws between the water shield and nut, then roll it back over the door. If necessary, apply a spray of adhesive or tape to help the water shield stick.
How do you remove a power window motor?
Remove the motor and regulator through the access port. With the pigtail disconnected, the power window motor and regulator will no longer be connected to anything inside the door. Reach into the large access port and pull them each out. The two are connected, so pulling one will remove them both.
What causes the window to get stuck on a Dodge Ram?
This article applies to the Dodge Ram 1500 (1994-2001). The power window actuator is responsible for moving the window up and down when you order it to do so. The window regulators on the Dodge Ram are a fairly common failure item, causing the windows to get stuck.
Do you need to disconnect power window regulator?
Be careful not to damage the regulator if you are only replacing the motor. Connect the regulator to the new motor. If you are only replacing the power window motor and not the regulator itself, you will need to disconnect it and connect it to your new power window motor.
How to replace power window motor on Dodge Ram?
Figure 1. Remove the T40 Torx screw. Pry the control panel off of the door and disconnect the two wire plugs. Figure 2. Disconnect the control panel plugs. Figure 3. Remove the door panel. Loosen the two 10mm bolt on the handle assembly. Remove the door lock rod from the handle assembly.
What is the regulator on a Dodge Ram?
This article applies to the Dodge Ram (2002-2008). The window motor on your Dodge Ram is part of a bigger component called a regulator. A regulator is comprised of two rails that push the window up, or pull it down, by use of the window motor.
Remove the motor and regulator through the access port. With the pigtail disconnected, the power window motor and regulator will no longer be connected to anything inside the door. Reach into the large access port and pull them each out. The two are connected, so pulling one will remove them both.
Be careful not to damage the regulator if you are only replacing the motor. Connect the regulator to the new motor. If you are only replacing the power window motor and not the regulator itself, you will need to disconnect it and connect it to your new power window motor.
How much does it cost to replace the back window on a Dodge Ram?
The backlite/back window serves as part of the structural support for the roof and is bonded with urethane that is hard to cut or clean off of any surface. Purchasing a new backlite will set you back over $400, so take this into consideration beforehand.
How to install a new power window motor?
Installing a New Power Window Motor 1 Slide the new motor and regulator back into place. Insert the power window motor and regulator back into the main service port in the door in exactly the opposite order that you removed them in when disassembling the door.
How to replace a power window motor with pictures?
How to Replace a Power Window Motor. 1. Remove the interior door panel. Most interior door panels are held in place with plastic interior fasteners. You can remove these fasteners by 2. Gently remove the plastic door cover. Beneath the door panel you will find a thin, translucent layer of
How do you replace a power window regulator?
Replace the mounting bolts. Hold each component in the appropriate position as you return the mounting bolts that secure both the power window motor and the regulator. Thread each bolt in by hand first, then use a wrench to tighten them. If a bolt doesn’t thread it properly, remove it and try again to prevent cross-threading them.
What’s the best way to fix a power window?
Pressing one palm on each side of the glass will allow your friend to hold the window up. Use masking tape to secure the window in place. With your friend holding the window up, pull off three or four strips of masking tape that are each about a foot long.