How long should brakes last on a Ford Explorer?

between 30,000 and 70,000 miles
How long do Ford Explorer brake pads last? Ford Explorer brake pads usually last between 30,000 and 70,000 miles depending on your driving habits.

Why do my rear brake pads wear out quickly?

Usually, it’s the front ones that wear faster, NAPA explains. That’s because braking shifts the car’s weight forward, which means the front rotors need to be stronger, NAPA explains. But there is a reason why rear brake pads can wear faster than expected: traction control and electronic stability control.

How much does it cost to replace brakes on a Ford Explorer?

Ford Explorer Brake Pad Replacement Cost Estimate. The average cost for a Ford Explorer brake pad replacement is between $163 and $210. Labor costs are estimated between $87 and $109 while parts are priced between $76 and $100.

How long should rear brake pads last?

Average brake life runs between 25,000 and 65,000 miles, though some people will have brake pads last beyond 80,000 miles. While it’s impossible to give an exact number, the 40,000-mile range is the general mileage to keep in mind when planning for vehicle maintenance.

Which brake pads wear out faster front or rear?

Your front brake pads will also wear down faster than your rear pads. The front of your vehicle handles a lot more weight transfer as you brake, causing more wear. Over time heat and friction also contribute to brake pad wear.

Why are my brakes soft after changing pads?

Air in the brake line(s) is the most common cause of a soft/spongy brake pedal. If air gets into the brake lines, it can prevent brake fluid from flowing properly, causing the brake pedal to feel spongy or soft. If the brakes are soft or spongy, this is a good time to change or flush the brake fluid.

Should you change front and rear brake pads at the same time?

You can replace your brake pads in pairs (the front or the rear) at the same time or separately. It’s also important to note that your front and rear brake pads wear at very different rates. The front brake pads do most of the work, causing them to wear faster and need replacement more often.

How long does it usually take to change brake pads?

Usually, changing a set of brake pads takes approximately 30 minutes to an hour. If you have a professional complete the work, expect to pay for about an hour’s worth of labor.

How to change the disc brake pads on a Ford Explorer?

This automotive maintenance tutorial was specifically written to assist owners of the fifth generation (2011, 2012, 2013, 2014 & 2015) Ford Explorer SUV in changing the rear disc brake pads, turning back the screw-in type caliper piston and lubricating the slider pins.

How do you replace rear disc brake pads?

If your new set of rear brake pads included replacement brake hardware, pull the old pad abutment or “anti-rattle” clips out of the top and bottom of the bracket before installing the new ones in their place. In order for the caliper to operate smoothly, the two caliper slider or “guide” pins need to be well lubricated.

How to replace the brake fluid cap on a Ford Explorer?

Tighten the lower 13mm caliper bolt in the counterclockwise direction (as seen from the outside of the SUV) to just past hand tight or about 24 ft-lbs of torque. If you haven’t already, replace the brake fluid reservoir cap by twisting it on in the clockwise direction.

How much torque do you need for rear disc brake pads?

The service manual specification for the rear caliper bolts is 24 lb-ft of torque (or 33 N.m.). Tighten the lower 13mm caliper bolt in the counterclockwise direction (as seen from the outside of the SUV) to just past hand tight or about 24 ft-lbs of torque.

How to replace rear brake pads on a Ford Explorer?

When replacing your brake pads on your Ford Explorer, you first need to jack up the vehicle and remove the tire. This will give you access to the brakes. Locate the caliper, remove the two bolts and slide the caliper off. Inside the calipers are the brake pads.

If your new set of rear brake pads included replacement brake hardware, pull the old pad abutment or “anti-rattle” clips out of the top and bottom of the bracket before installing the new ones in their place. In order for the caliper to operate smoothly, the two caliper slider or “guide” pins need to be well lubricated.

How do you remove a brake caliper from a car?

This will give you access to the brakes. Locate the caliper, remove the two bolts and slide the caliper off. Inside the calipers are the brake pads. Pry out the outside brake pad off first, then the inside pad. Then it’s time to reverse the process!

How to check for brake fluid leak in Ford Explorer?

It’s also a good idea to regularly check your driveway for drops of brake fluid which may indicate a leak, check the brake fluid level in the reservoir, and verify that the lug nuts are still tight after a short test drive. For more, check out my other Ford Explorer DIY Repair & Maintenance Guides.