How do you remove an alternator from a Pontiac?

How do you remove an alternator from a Pontiac?

Disconnect any wire clamps that are on the clip at the alternator’s end frame, then remove the rubber clamp and nut. These extra fasteners are not on all Pontiac models. Disconnect the electrical connector for the alternator. Remove the alternator by disconnecting its bolts.

How do you remove serpentine belt from alternator?

Remove the serpentine belt from the alternator. Disconnect the wiring harness and the battery cable from the back. Now start loosening the two 13mm bolts on the back of the alternator and the 15mm bolt on the front.

How do you connect a new alternator to a car battery?

Move the new alternator into position. Connect the exciter wire, then thread in the bolts by hand. Tighten the bolts down and then reconnect the wires on the back of the alternator. Slip the serpentine belt over the alternator pulley, then tighten the tensioning bolt. Reconnect the battery and start the car.

What is the alternator on a Chevy Camaro?

The alternator is the central power unit of your car’s charging system. This article will show you how to install a new one. This article applies to the Chevrolet Camaro and Pontiac Firebird (1990-2002).

How much does a Pontiac Firebird alternator cost?

Advance Auto Parts has 100 different Alternator for your vehicle, ready for shipping or in-store pick up. The best part is, our Pontiac Firebird Alternator products start from as little as $41.99. When it comes to your Pontiac Firebird, you want parts and products from only trusted brands.

How do you change an alternator in a car?

Slip the serpentine belt over the alternator pulley, then tighten the tensioning bolt. Reconnect the battery and start the car. Pay careful attention to how the new alternator is running. Listen for any sounds from the alternator and check the voltmeter in the dash for any fluctuations. If it checks out okay, then you’re all done.

The alternator is the central power unit of your car’s charging system. This article will show you how to install a new one. This article applies to the Chevrolet Camaro and Pontiac Firebird (1990-2002).

Remove the serpentine belt from the alternator. Disconnect the wiring harness and the battery cable from the back. Now start loosening the two 13mm bolts on the back of the alternator and the 15mm bolt on the front.

How do you put an alternator in a bracket?

Position the new alternator in the bracket and slide the bolts back into place, tightening the bolts with a socket wrench until you can just barely slide the alternator on the bracket.

How do you hook up an alternator to a Pontiac Montana?

Reattach the electrical wire connector to the alternator terminal by placing the connector and the nut on the terminal and securing with a socket wrench. Connect the negative battery cable to the battery of the Pontiac Montana with an open end wrench. Determine which alternator your Pontiac Grand Am will need.

How do you install an alternator on a 3.4 L engine?

Take the mounting bolts (and nuts for a 3.4 L engine) off of the alternator with a socket wrench and remove the alternator assembly. Install the new alternator assembly and tighten the mounting bolts to 15 foot pounds with a torque wrench for most models.

How do you replace an alternator on a Pontiac Grand Prix?

Plug in the electrical connectors to the alternator and install the drive belt. Reposition the oil dipstick tube to its original position and tighten the bolt for the oil dipstick tube with a socket wrench. Replace the air cleaner assembly and connect the negative battery cable. Determine which alternator your Pontiac Grand Prix will need.

How do you remove an alternator from a car?

Remove the electrical leads from the alternator using a wrench to remove the nuts. Remove the bolts from the alternator with a socket and ratchet and pull it off of the engine. Put the new alternator on the engine and tighten the mounting bolts with the socket and ratchet. Connect the electrical leads and tighten the nuts with the wrench.

Where is the alternator on a Pontiac Montana?

Connect the battery terminal and tighten the terminal nut with the wrench. Detach the negative battery cable from the battery of the Pontiac Montana with an open end wrench and move the cable so that it is not touching any metal objects. Locate the alternator in the front of the engine on the passenger side of the engine compartment.

Take the mounting bolts (and nuts for a 3.4 L engine) off of the alternator with a socket wrench and remove the alternator assembly. Install the new alternator assembly and tighten the mounting bolts to 15 foot pounds with a torque wrench for most models.

How to change serpentine belt on Camaro Firebird?

Remove the bolts holding the lid to the front core support, and remove the bolts holding the intake tube to the throttle body. Cold air intakes and other aftermarket solutions may be different in this regard. Figure 1. SLP lid on LS1. Before doing anything, check to see if your belt routing diagram is still there in your engine bay.