How do you change the throttle position on a Cavalier?

How do you change the throttle position on a Cavalier?

Use the torx screwdriver or socket to loosen the two bolts on the Cavalier’s throttle position sensor, then remove them by hand. Pull the throttle position sensor off; you may have to wiggle it back and forth to remove it. Place the new throttle position sensor in its place.

What do I need to replace TP sensor on Cavalier?

Replacing the TP sensor is simple, quick and inexpensive. It is recommended to use GM factory parts when replacing items on your Chevrolet Cavalier. Disconnect the negative battery cable for safety and gather the tools and parts needed for replacement. Locate the throttle position sensor.

How do you remove a Cavalier sub frame?

How to Remove a Cavalier Subframe. Loosen the 18mm rear sub-frame bolts and unbolt the rack and pinion from the sub-frame. Support the sub frame with a floor jack. Remove the six 18mm and two 15mm sub-frame bolts using a socket and ratchet. Lower the sub-frame to the ground. Slide the sub-frame from under the car and transfer the control arms,…

How do you adjust the alignment of a tire?

Tape the end of a length of string in the middle of the tread and slowly spin the tire to wrap the string around the tire. Keep the string centered in the tread. Once the the two ends of the string meet, tape the other end into place.

What does the TP sensor on a Cavalier do?

by Leonardo R. Grabkowski. The throttle position sensor, also called the TP sensor, helps to regulate the throttle position on a car’s engine. A faulty TP sensor can cause an illuminated check engine light in your Cavalier, as well as cause the engine to run inefficiently. Replacing the TP sensor is simple, quick and inexpensive.

How do you remove the throttle position sensor?

Pull the throttle position sensor off; you may have to wiggle it back and forth to remove it. Place the new throttle position sensor in its place. Tighten the torx screws and reconnect the electrical connection and the negative battery cable.

When did the fuel injected Cavaliers come out?

Place the new throttle position sensor in its place. Tighten the torx screws and reconnect the electrical connection and the negative battery cable. All Cavaliers sold after 1995 are fuel-injected. Most models before 1995 are also fuel-injected.

Where is the throttle position sensor on a Cavalier?

Locate the throttle position sensor. The sensor is attached to the rear of the throttle body. Disconnect the electrical connection from the sensor. Use the torx screwdriver or socket to loosen the two bolts on the Cavalier’s throttle position sensor, then remove them by hand.

What happens when the throttle position sensor fails?

The throttle position sensor can fail in several ways, all of which result in poor fuel economy at best, and performance limitations that may create safety hazard for you and other motorists at worst. This sensor can fail gradually, or all at once. In most cases, the Check Engine Light is illuminated if a TPS failure is detected.

What does it mean when your car throttles up while driving?

In these cases, the TPS isn’t providing the right input, the onboard computer cannot direct the engine to work properly. When the car accelerates while driving, it usually means the butterfly valve inside the throttle has closed up and pops open suddenly when the driver presses on the accelerator.

Place the new throttle position sensor in its place. Tighten the torx screws and reconnect the electrical connection and the negative battery cable. All Cavaliers sold after 1995 are fuel-injected. Most models before 1995 are also fuel-injected.

What does the TP sensor on a car do?

The throttle position sensor, also called the TP sensor, helps to regulate the throttle position on a car’s engine.

Use the torx screwdriver or socket to loosen the two bolts on the Cavalier’s throttle position sensor, then remove them by hand. Pull the throttle position sensor off; you may have to wiggle it back and forth to remove it. Place the new throttle position sensor in its place.

by Leonardo R. Grabkowski. The throttle position sensor, also called the TP sensor, helps to regulate the throttle position on a car’s engine. A faulty TP sensor can cause an illuminated check engine light in your Cavalier, as well as cause the engine to run inefficiently. Replacing the TP sensor is simple, quick and inexpensive.

Pull the throttle position sensor off; you may have to wiggle it back and forth to remove it. Place the new throttle position sensor in its place. Tighten the torx screws and reconnect the electrical connection and the negative battery cable.

The throttle position sensor, also called the TP sensor, helps to regulate the throttle position on a car’s engine.