How do you calibrate a Honda seat?

Settle the seat weight sensors after the seat is properly set-up by doing this:

1. Drive the vehicle at 22 mph (36 km/h), then park the vehicle on level ground.
2. Turn off the engine and HVAC system. Close the windows and doors.
3. During the calibration procedure, DO NOT sit in or touch the front passenger’s seat.

How do you raise the passenger seat in a Honda Civic?

To raise: Pull it upward. To lower: Push it down while pressing the release button. Head restraints can be removed for cleaning or repair.

What is Opds sensor?

OPDS is Occupant Position Detection System It’s used to detect the size of the occupant in the passenger seat. If it detects a child sitting in the seat, it will not deploy the airbag.

What is seat occupancy sensor?

The Seat Occupancy sensor is a magnetically operated push button sensor with a simple push-fit clip mounting configuration, allowing the passenger safety system to determine the presence of an object or person in a seat.

How do car seat belt sensors work?

When someone sits on the seat, the pressure sensor signals the occupant’s weight to the ECU. It reads the passenger’s seating position and determines if they’re wearing a seat belt. It also has a seat belt tension sensor that allows the OCS to interpret the pressure created when a child seat is fitted.

Is the Honda Civic too low?

Too low to go. The current generation is actually lower in height than the last one, and compared to top-selling compact cars like the Toyota Corolla, Nissan Sentra, and Ford Focus, its height of 55.7 inches is lower by at least 2 inches.

How do you move the front seat in a Honda Civic?

You can adjust the seat with the ignition switch in any position. Make all seat adjustments before you start driving. Push the horizontal switch forward or backward to move the seat forward or backward. Pull up or push down on the front of the switch to move the seat bottom’s front edge up or down.

What is a faulty OPDS sensor?

It’s used to detect the size of the occupant in the passenger seat. If it detects a child sitting in the seat, it will not deploy the airbag. The reason the OPDS set a diagnostic code is because it has an internal failure relating to electrical interference. The updated part should eliminate this problem.

How does a seat occupancy sensor work?

June 15, 2018 / The Vmanx seat occupancy sensor is used to detect if a passenger is sitting in the seat. When a person is sitting in the seat, the sensor on the seat produces pressure sensing. Then the buzzer that triggered the sensor connection sounds an audible alarm.

How does a car know if someone is sitting in the passenger seat?

When someone sits on the seat, the pressure sensor signals the occupant’s weight to the ECU. The ECU then sends that data to the airbag, which has its own control unit. It reads the passenger’s seating position and determines if they’re wearing a seat belt.

When do seat weight sensors need to be recalibrated?

Requires recalibration (SWS Initialization) when seat weight sensors or the ODS/SWS unit is replaced. When seat weight sensors were first added, there was a separate SWS unit mounted under the front passenger’s seat.

When do you need to recalibrate the passenger side mirror?

Any time you R&R or R&I the camera, the passenger side-view mirror — or the mirror cover. Any time you R&R or R&I the passenger-side door — or any time you merely adjust its position. Kaboos summed it up as “if you do anything with that mirror,” it needs to be recalibrated.

When does a Honda need to be calibrated?

The display also measures distances between other vehicles and the Honda. Kaboos said it must be calibrated under many circumstances, including: Any time you R&R or R&I the camera, the passenger side-view mirror — or the mirror cover. Any time you R&R or R&I the passenger-side door — or any time you merely adjust its position.

What causes SRS to not initialize seat assembly?

If the SRS system initializes, the problem is in the original seat assembly. If it still won’t initialize, the problem is in the SRS unit, or another part of the SRS system. Due to seat movement and wear, damaged seat wiring harnesses may cause DTCs and SRS/ODS initialization failure.