Where can I get my Check Engine Light code read?
Where can I get my Check Engine Light code read?
You can. All that you need to check your own light is an OBD-II reader, which can pull codes that help you find out what’s wrong with your car. If you don’t have a code reader, keep reading to learn the most common causes, and then bring your car to your local AutoZone to find out why your Check Engine Light is on.
Will a code reader tell me why my Check Engine Light is on?
A professional mechanic can connect a scan tool or code reader to your vehicle’s OBD port, which is usually located in the steering column, in order to retrieve this diagnostic code. This code will not tell your mechanic the exact reason why your check engine light turned on.
Can you clear Check Engine Light with obd2 Scanner?
With the OBDII Scan Tool MS309 from OxGord, you can easily read diagnostic codes, clear trouble cods (DTC’s), and turn off the check engine light (MIL) on US based vehicles from 1996.
Does AutoZone do free OBD scans?
We can help you get a reading yourself. Borrow an OBD reader to get a Check Engine Light reading with the AutoZone Free Fix Finder Service. It’s a simple task that takes less than two minutes.
How do you read a engine code without a scanner?
A. Using The Ignition Key
- Step 1: Turn The Ignition Key. Switch ON and OFF the ignition key without running the engine.
- Step 2: Check Your Dashboard. Right after the dash lights come up, they’ll turn off, except one—usually the service engine light.
- Step 3: Note And Interpret The Check Engine Codes.
How do I clear my engine light with OBD2?
Press the “erase/clear” button on your scanner, then turn off the key and disconnect it. Clearing any codes present will turn off your check engine light temporarily. After pressing “erase/clear” and waiting until you see a “no codes” message, you can turn off your vehicle and disconnect the scanner.
How do you reset the check engine light on an OBD2?
Connect the OBD2 dongle to the connector. Make sure the adapter is tightly attached but don’t use too much force. Turn ignition key to the ON position. Don’t start the engine because to reset the light, the engine shouldn’t be running.
Will AutoZone read check engine codes?
Many drivers don’t realize that AutoZone, the nation’s largest auto parts chain, will do the following services free of charge: Read the codes on your check engine light. Test your battery’s voltage. Check your alternator and starter.
Where can I read car codes for free?
If you have a problem with your car and you don’t know what it is, most auto part stores (such as AutoZone, Pep Boys and Advance Auto Parts) will provide a free diagnostic code reading. It is also called an OBD reading.
How to read a check engine light code?
How to Read Codes From Your Check Engine Light (For Older Cars) Step 1: Find Your Vehicle’s Diagnostic Plug . The first step is to find your vehicles diagnostic plug. The one in my car was a small blue plug that was Step 2: Bridge the Wires. Step 3: Watch the Flashing Light and Decipher the Code.
How do you check the Check Engine light?
Put your key in the ignition and switch the vehicle to “on.” Do not start the vehicle. Once the lights on the dash come on, turn off all the vehicle’s accessories, like the radio. Then, press the “read” button on the scanner to access the check engine light code.
Where to get a “check engine” light read?
The first step is to read the check engine light code provided by the car’s computer system. This is the information that’s been logged by the sensors in your engine. It can be read with OBD II scanners or readers through a connection (OBD port) usually located under the steering column.
Where can I test the Check Engine light?
Disconnecting car battery cables In this step, you should use a wrench to remove positive and negative cables. Apply The Battery Disconnecting Technique (Source: Wikihow) Draining remaining electricity Next thing you should do is to press and hold the car horn for about 30 seconds. Waiting and reconnecting the battery
