Can a fuel pump be replaced in a K5 Blazer?
Can a fuel pump be replaced in a K5 Blazer?
If your tank is not quite empty, pour the remaining fuel out into a suitable container (even if it’s only a couple of gallons, having fuel in the tank sloshing around makes it harder to reinstall the tank). You can now replace the fuel pump and in tank filter (most call this a sock).
Can a Chevy C / K 1500 run without fuel?
Also I haven’t fully checked the Spark, but the Truck run’s fine when you spray Starting fluid into the Throttle body. Any suggestions on why the truck isn’t accepting the fuel, it cranks fine, just wont run without starting fluid. these trucks have to have between 55-65psi of fuel to run.
What kind of fuel pump does a Chevy Silverado need?
It turned out the pump I put in was for a 96 C1500, which has a throttle body system and the pump only produced 20-30psi. The Fuel injection in the Silverado needs 55-65psi. Be very careful you didn’t put the wrong fuel pump in!!
How do you change the gas tank on a GMC pickup?
Add fuel to the tank and prime the fuel system by turning the key on and letting the fuel pump run briefly and then turning it off. Repeat this several times to be sure the pump has primed and filled the fuel lines with fuel. Test-run the truck and check for any leaks around your connections.
Where can I get a new fuel pump for my Chevy k1500?
A fuel pump replacement for Chevy K1500 eliminates these problems, so shop the incredible selection at AutoZone. Take your pick from our line of custom K1500 fuel pumps today and enjoy great benefits like free battery charging and engine diagnostic testing during your next in-store visit.
What to do if your Chevy fuel pump fails?
Chevrolet fuel pump failures are a common and growing problem. If you have a fuel pump harness connector that looks like the flat one on the right or the square one at the bottom, then consider replacing it when replacing the pump. More details about this are below, but you might want to download your Chevy manual to help.
Where is the connector on a Chevy fuel pump?
When you get the Delco replacement parts it comes with a new connector on the fuel pump side. The problem is the connector on the vehicle side of the harness. In the online Chevrolet repair manual I use, a Tech Tip states, the connector should be replaced with the fuel pump assembly.
When did the Chevy fuel pump come out?
It started on Chevrolet truck models from 1996 to 2003 model years, but has expanded to other models as the connector and pump assemblies are not aging well. In fact, I have a financially strapped friend with an 04 Silverado that now caries a heavy rubber mallet in the truck.
Where is the oil pressure switch on a K5 Blazer?
The oil pressure switch is located towards the top of the block near the distributor (this is the one we’re concerned with now), and the oil pressure sending unit is near the oil filter. Even if it’s the oil pressure switch, you should see voltage at the fuel pump for 2 seconds after turning on the ignition.
Where is the fuel pump connector on my Blazer?
This connector is located, at least on my truck, on the inside of the frame, driver’s side, over the rear axle. The pigtail from the fuel pump to the connector seemed OK, so that left the fuel pump itself. There’s a short red test lead on the fuel pump relay connector.
How do you remove a gas tank from a blazer?
Make sure all the lines, hoses, and connectors are disconnected. Now that the tank is out, clean off the top and blow off with compressed air or a brush. Gas Fumes Can Explode, so Be Cautious! You can remove the fuel pump from the tank by tapping the ring with with a screw driver and working it around until it’s loose.
Where is the fuel pump connector on a K5 Blazer?
Using a test light I was able to determine that power was coming out of the fuel pump relay (mounted to the firewall passenger side, grayish wire if I recall correctly) and making it all the way back to the connector at the fuel pump. This connector is located, at least on my truck, on the inside of the frame, driver’s side, over the rear axle.
Where to replace fuel filter in K5 Blazer?
Hand tighten as best you can, then position the two wrenches so that you can squeeze them together with one hand to tighten (again not easy). It’s a good idea to replace the fuel filter at this time if you have not done so recently (on mine it’s on the inside of the frame under the passenger side door area).
The oil pressure switch is located towards the top of the block near the distributor (this is the one we’re concerned with now), and the oil pressure sending unit is near the oil filter. Even if it’s the oil pressure switch, you should see voltage at the fuel pump for 2 seconds after turning on the ignition.
How do you remove fuel pump from Blazer?
You can remove the fuel pump from the tank by tapping the ring with with a screw driver and working it around until it’s loose. There is a special tool for this, but I just used a screw driver.
