When to scan for a new ABS module?

This scan was performed when the module and cluster where going hay wire. EPC, check engine, steering wheel, ABS, Brake light were all on.

Where can I buy ABS modules for a Harley Davidson?

I don’t know if you still have your ’08 but there is a place on Amazon that carries the ABS modules for Harley. It is AD Auto Parts Store. part #40601-08A. Received the HD brake fluid recall the week my ABS module failed on my 2009 FLHTCU.

When did my 2009 Road King Classic ABS unit fail?

2009 Road King Classic, abs unit failed in second year, I don’t trust my dealer here in Houston, They left a battery wire off my led lights which caused them to acquire a ground through the engine light system.

Are there any other vehicles that use ABS?

There are countless vehicles on the road, other than Harley Davidson, that utilize ABS systems and Dot 4 brake fluid. It is unsettling to us why Harley Davidson is, seemingly, the only vehicle manufacturer failing in this area.

When do you replace an ABS control module?

Other vehicles may require the two components to be replaced as a unit. This is dependent on how well you can access it and how the new module is sold. Step 2: Move onto part 3 or part 4. Skip to part 4 if you only need to remove the module and not the solenoid block and motor.

Can a solenoid block be replaced with an ABS module?

Sometimes, the module will be replaced along with the solenoid block and other times it will not. This is dependent on the design and location of the ABS unit which is based on the manufacturer’s design, build choices, and how the replacement module is sold. Step 1: Refer to your specific repair manual to locate the ABS module.

Do you need an ABS module coded to your Vin?

This is a repair and return service where the module is rebuilt, tested, and shipped back. MyAirbags will rebuild your original part to make it as good as new! You will not need your ABS module coded to your vehicle VIN because it is the original module.

How do you install an ABS system in a car?

This should be a simple job and one that you can complete away from the main body of the vehicle. Reverse the previous steps to install the ABS unit back into the car. Gently slide it into position and replace any other engine components you removed to allow you access to the ABS system.

What happens if the ABS coding is wrong?

Click to expand… As best I know, the ABS coding for a given car should not change when the correct replacement part is installed. If the coding is wrong, one would expect a 01042 – Control Module; Not Coded or something to that effect to be flagged. Thus, so far, so good.

What is a c0710 and c0455 trouble code?

GM has issued a service bulletin PI0639C to address a service stability message and trouble codes C0710 and C0455 for the vehicles listed below. In addition to the information in the service bulletin, I’m adding more information on how the system works along with additional tips on how to diagnose problems What is a C0710 and C0455 trouble code?

What to do about service stability c0710 c0455?

If all those items check out, proceed with the recommended GM fix. an intermittent C0710, C0455 Service Stability condition. The advice is to remove the connector to the SWPS and use a nylon brush to apply dielectric grease to the terminals inside the connector and the SWPS.

How much does it cost to fix a c0455 code?

The cost of diagnosing the C0455 code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour. The Electronic Brake Control Module (EBCM) receives several inputs from the steering wheel position sensor.

How to write code for new ABS module?

Same coding should be the result with a copy and paste if that is the case. Don’t shut off ignition at this point and I recommend it be done while engine is running. Perform broadcast and erase DTC ‘s………..see what’s left on installed list for DTC ‘s as a reference save.