What are the running lights on a 1999 Ford Ranger?
What are the running lights on a 1999 Ford Ranger?
Daytime running lights, sometimes referred to as DRLs or DTRs, are lights that switch on automatically when your 1999 Ford Ranger is turned on and in drive. Since the daytime running lights are on whenever you are driving your Ranger, they are often the first bulbs to burn out.
Where is the daytime running light module located?
Typically, the daytime running light module is located under the dash or in the engine compartment. The exact location can be found in the vehicle repair manual. Step 1: Disconnect the negative battery cable. Disconnect the negative battery cable and set it aside. Step 2: Unbolt the module.
How does the Ford daytime running lights work?
The system is activated when the ignition switch is in the ON position, the headlamp switch is in the OFF position, and the parking brake is released. What it means: The DRL “Module” does everything. It does not use a resistor but instead uses switches to provide lower voltage to the High beams. Not sure about to much more like wiring, etc.
Where are the running lights on a Ford truck?
If not you will just have a cap on the wire harness. The blue arrow points to it’s location. If you lay on your back with your feet out the front of the truck you can look under the left side and see the wiring harness for the DRL Resistor (This photo is taken from that view).
Daytime running lights, sometimes referred to as DRLs or DTRs, are lights that switch on automatically when your 1999 Ford Ranger is turned on and in drive. Since the daytime running lights are on whenever you are driving your Ranger, they are often the first bulbs to burn out.
When to replace the DRL on a Ford Ranger?
DRL Replacement 1998-2005 Ford Ranger – 1999 Ford Ranger XLT 4.0L V6 Extended Cab Pickup (4 Door) Video instructions on how to replace a daytime running light on a 1999 Ford Ranger XLT 4.0L V6 Extended Cab Pickup (4 Door). The video provides steps for replacing a burnt out DRL or DTR on a 1999 Ford Ranger XLT 4.0L V6 Extended Cab Pickup (4 Door)
If not you will just have a cap on the wire harness. The blue arrow points to it’s location. If you lay on your back with your feet out the front of the truck you can look under the left side and see the wiring harness for the DRL Resistor (This photo is taken from that view).
When did Ford start using daytime running lights?
It is primarily intended for 1990’s-2000’s Ford trucks but most likely also applies to other Ford models and years. Why was this article created? There seems to be a lot of confusion about Daytime Running Lights (DRL) on the Ford F150 trucks.
DRL Replacement 1998-2005 Ford Ranger – 1999 Ford Ranger XLT 4.0L V6 Extended Cab Pickup (4 Door) Video instructions on how to replace a daytime running light on a 1999 Ford Ranger XLT 4.0L V6 Extended Cab Pickup (4 Door). The video provides steps for replacing a burnt out DRL or DTR on a 1999 Ford Ranger XLT 4.0L V6 Extended Cab Pickup (4 Door)
Where are the fuses on a 1998 Ford Ranger?
Passenger Compartment Fuse Box № A Circuits protected 4 10 Left Headlamp 5 10 1998-1999: Data Link Connector (DLC) 6 15 2000: Overdrive, Back-up Lamps, DRL, 4×4 7 7.5 Right Stop/Turn Trailer Tow Connector
The system is activated when the ignition switch is in the ON position, the headlamp switch is in the OFF position, and the parking brake is released. What it means: The DRL “Module” does everything. It does not use a resistor but instead uses switches to provide lower voltage to the High beams. Not sure about to much more like wiring, etc.
What are the fuses on a 1998 Ranger?
Passenger Compartment Fuse Panel No. AMPS Circuits protected 25 7.5 1998-1999: Generic Electronic Module (GE 26 10 Battery Saver Relay, Electronic Shift Re 27 15 1998-1999: Electric Shift, Backup Lamps, 28 7.5 Generic Electronic Module (GEM), Radio
